Southland OMD-525X Скачать руководство пользователя

Страница: 14 / 36

2.4

Gas Connections

The OMD-525X can accept either a TO2-1x or TO2-2x (for CO2 applications, i.e. natural gas) oxygen sen-

sor for trace oxygen analysis. For percent measurement, the OMD-525X can accept either a PO2-160 or

PO2-24 (for CO2 applications) oxygen sensor. For high purity percentage levels of oxygen the PO2-1120

sensor should be used. For a hybrid application where the user is monitoring oxygen from 50 ppm up to

21.0% with regular exposure to ambient air, consider the TO2-19 Hybrid Oxygen Sensor. For help selecting

a sensor, contact your local sales rep or the factory.

Prior to installing the sensor, it is important to make sure that the analyzer gas lines are hooked up and

the unit is ready to purge with a zero or process gas. Connect the zero gas line and set your flow between

0.50 - 5.0 SCFH.

To Install the Sensor:

- Remove the four screws and open the front of the analyzer.

- Remove the cell holder cap by unscrewing the stainless steel collar.

- Lift up on the top of the sensor housing and set it to the side.

- Inspect O-ring for cracking, replace if necessary. Always lube your O-rings!

- Remove the sensor from its box. With scissors, open nitrogen purged packaging

and remove the sensor.

- Visually inspect sensor for damage, if damaged notify the factory immediately.

- Remove the shorting tab across the back of the sensor circuit board (red

tape).

- Place the sensor inside the housing with the metal mesh screen facing down and

the circuit board contacts facing up.

- Return upper portion of the sensor housing to the stainless steel bottom. Tighten

collar. Hand tight is acceptable to create an airtight seal.

- Immediately start purge of zero gas.

- If the analyzer has not been calibrated, refer to section 4.1 for more information.

** Sensor should not be exposed to ambient air for more than 2 minutes. Extended periods of

exposure can damage the low end sensitivity and response time.

CAUTION: Prior to installing the oxygen sensor read section 4.1 on per-

forming a span calibration.

Oxygen Sensor Front and Rear View

2.5

Installing the Oxygen Sensor

Gas Connections are made via compression tube fittings directly on the analyzer, inlet / outlet can flow in

either direction. Various tube fittings sizes are available, check with the build sheet for specific gas con

nection sizes.

Designed, Tested, and Assembled in California, USA

4045 E. Guasti Rd. #203 Ontario, CA 91761 USA : 1-949-398-2879 : [email protected] : www.sso2.com

Installation

OMD-525X Oxygen Analyzer

Содержание OMD-525X





































Результаты поиска

Содержание OMD-525X

Отзывы:

Похожие инструкции для OMD-525X

Бренды по названию

Популярные бренды

Southland OMD-525X, Инструкция по эксплуатации

Результаты поиска

Содержание OMD-525X

Отзывы:

Похожие инструкции для OMD-525X

Бренды по названию

Популярные бренды