background image

22 

 

LOAD 

Ext.File 

SAVE 

Int.File 

FILE 

I/O 

Envi 

CK 

(channel 

control) 

Test 

SYSTEM 

OS 

IR 

AC parameters 

DC 

AC 

STEP

01/0

SETUP 

File modification and 
inspection 

Start Test 

TEST 

Chapter 4 Basic operation 

 

4.1

 

Interface structure overview 

The following figure is the interface structure: 

 

Figure 4-1 Operation Steps 

Interface Instructions: 

 

The  first  column  of  the  interface  structure  is  called  according  to  the  panel  function  button. 

TEST interface cannot modify parameters. 

 

The second column of the interface structure is the parameter structure of the initial interface. 
For example, the SETUP interface defaults STEP 01/01: scenario step 1, total steps 1

AC: AC 

withstand  voltage  test  interface,  AC  parameters:  Other  parameters  are  test  parameters  of  AC 

withstand voltage. 

 

The third column of the interface structure is the function switching interface. These features 

can be changed when some feature identifiers are selected in the second interface, the relevant 

parameters  of  this  interface  will  change.  For  example  if  the  AC  is  changed  to  DC,  the 

instrument  will change  the  AC  withstand  voltage  test  mode  to  the  DC  withstand  voltage  test 

mode, the 'AC parameter' of the current interface will change to the 'DC parameter' that the DC 

withstand voltage needs to be set. 

Note: The instrument only saves data changes when switching interfaces. After modifying 

the data in the SETUP interface and SYSTEM interface, please switch the interface to 

Содержание ST9010 Series































































Отзывы: