Sorvall WX 100 Ultra Скачать руководство пользователя страница 79

Страница: 79 / 131

Operation

Rotor management

Thermo Scientific

WX Ultra Series

2-63

Select “T-890” rotor.

After checking the specifications of the
rotor, enter “Yes”.

As the cursor has been moved to the
S/N field, enter serial No. of the rotor
by using numeric keys.
(Do not press the ENTER key.)

Registration of an unused rotor is fin-
ished by pressing the ENTER key.

Enter the total number of runs in the
Runs field. (Do not press the ENTER
key.)

Enter the total number of hours in the
Hours field by using numeric keys. (Do
not press the ENTER key.)
Note: Enter this running time up to one
decimal place in units of hour.
1200 hours 24 minutes ---> 1200.4

Press the ENTER key.

• Specifications of the T-890

rotor are displayed.

• The display switches to the

Rotor Management screen.

• You can enter a serial

number of the rotor.

• The cursor moves to the

Runs field. You can enter the
total number of runs.

• The cursor moves to the

Hours field. You can enter
the number of hours.

Содержание WX 100 Ultra




































































































































Результаты поиска

Содержание WX 100 Ultra

Отзывы:

Бренды по названию

Популярные бренды

Sorvall WX 100 Ultra, Инструкция по эксплуатации

Результаты поиска

Содержание WX 100 Ultra

Отзывы:

Бренды по названию

Популярные бренды