manualshive.com logo in svg

Sorvall WX 100 Ultra, Инструкция по эксплуатации

Поделиться
Скачать
Sorvall WX 100 Ultra Скачать руководство пользователя страница 6

Preface - Intended use and safety definitions

Important safety reminder

iv

WX Ultra Series

Thermo Scientific

Important safety reminder

Certain potentially dangerous conditions are inherent to the use of all centrifuges. To ensure safe 
operation of this centrifuge, anyone using it should be aware of all safe practices and take all 
precautions described below and throughout these operating instructions.

DANGER  

• Before removing any cabinet panel (such as for maintenance or repair), always turn 

the main Power Switch OFF and unplug the centrifuge, then wait at least three 
minutes to eliminate the potential for severe electric shock.

WARNING

• Never exceed the maximum rated speed of the installed rotor; to do so can cause rotor 

failure.

• Always reduce (derate) rotor speed whenever:

1. The rotor speed/temperature combination exceeds the solubility of the gradient 

material and causes it to precipitate.

2. The compartment load exceeds the maximum allowable compartment load (or design 

mass) specified for your rotor.

Failure to reduce speed under these conditions can cause rotor failure.

• Always inspect the rotor as specified in your rotor manual. Do not use a rotor that 

shows signs of damage or corrosion.

• Centrifuges routinely deal with high energy levels and could move suddenly in the 

unlikely event of rotor failure. During centrifuge operation, never lean on or move the 
centrifuge, keep the surrounding area clear of objects (including all hazardous and 
flammable materials), and do not work on top of or next to the centrifuge (as a rule, 
keep people and objects at least 300 mm [12 inch] away).

• Never unlock the chamber door, attempt to open the door, or otherwise attempt to 

touch the rotor while it is rotating. In the event of a power outage, it can take more 
than three hours for the rotor to stop - be sure to wait at least three hours before 
opening the door.

• Never attempt to override or otherwise disable any safety features.

• When using radioactive, toxic, or pathogenic materials, be aware of all characteristics 

of the materials and the hazards associated with them in the event leakage occurs 
during centrifugation. If leakage does occur, neither the centrifuge nor the rotor can 
protect you from particles dispersed in the air. To protect yourself, we recommend 
additional precautions be taken to prevent exposure to these materials, for example, 
use of controlled ventilation or isolation areas.

• Always be aware of the possibility of contamination when using radioactive, toxic, or 

pathogenic materials. Take all necessary precautions and use appropriate 
decontamination procedures if exposure occurs.

Содержание WX 100 Ultra




































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды