Sorvall WX 100 Ultra Скачать руководство пользователя страница 62

Страница: 62 / 131

Operation

How to use the FUNCTION field

2-46

WX Ultra Series

Thermo Scientific

Canceling the RTC settings

The canceling procedure varies depending on whether the RTC run is started (START is pressed) or

not.

Making a change to date and time set-
tings
(1) Select “Setting stop time” or “Set-
ting start time”.
To change the “Setting stop time”,
press

(2) Perform process 4 and later ones in

1. How to perform an RTC run

men-

tioned above and change the date and
time settings.

See Section

1. How to perform an RTC run

• The screen switches to a

screen where you can enter a
stop time (or start time).

Step

Key operation

Screen display and considerations

(1) While in the Run Screen, use cursor
keys to move the cursor to PROG • RTC
and then press ENTER key.

(2) Use cursor keys to move the cursor
to RTC and then press ENTER key.

>> The message indicator displays RTC.

• The FUNCTION field

switches to the RTC field.

Содержание WX 100 Ultra




































































































































Результаты поиска

Содержание WX 100 Ultra

Отзывы:

Бренды по названию

Популярные бренды

Sorvall WX 100 Ultra, Инструкция по эксплуатации

Результаты поиска

Содержание WX 100 Ultra

Отзывы:

Бренды по названию

Популярные бренды