Sorel TDC 4 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 52

Sorel TDC 4 Скачать руководство пользователя страница 38

38

Protective functions

menu 6

11

11

11. Protective functions

Menu “6. Protective functions” can

be used to activate and set various

protective functions.

Caution

The menu is closed by pressing

“esc” or selecting “Exit settings”.

This does not under any

circumstances replace

the safety facilities to be

provided by the customer!

11.1Seizing protection

menus 6.1 / 6.1.1 - 6.1.2

If the seizing protection is activated, then the controller switches the relay

in question and the connected consumer on every day at 12:00 and on

Sundays at 12:00 for 5 seconds in order to prevent the pump and/or the

valve from sticking after an extended stationary period.

Setting range R1: daily, weekly, off/default setting: daily
Setting range R2: daily, weekly, off/default setting: daily

11.2 Frost protection

menus 6.2 / 6.2.1 - 6.2.2

A two-stage frost protection function can be activated. In stage 1 the

controller switches the pump on for 1 minute every hour if the collector

temperature drops below the set value “Frost stage 1”.

If the collector temperature drops further to the set value “Frost stage 2” the

controller switches the pump on continuously.

If the collector temperature then exceeds the value “Frost stage 2” by 2°C,

then the pump switches off again.

Frost protection setting range: on, off/default setting: off
Frost stage 1 setting range: from -25°C to 10°C or off/default setting: 7°C
Frost stage 2 setting range: from -25°C to 8°C/default setting: 5°C

Caution

This function causes energy to be lost via the collector! It is nor-

mally not activated for solar systems with antifreeze.

Observe the operating instructions for the other system compo-

nents!

«
...
36
37
38
39
40
...
»

Содержание TDC 4





















































Отзывы:

Нет отзывов