Sorel TDC 4 Скачать руководство пользователя страница 36

36

A setting must be made as to which storage tank (storage tank sensor) 

has  priority  for  charging.  Charging  of  the  lower-priority  storage  tank  is 

interrupted at regular intervals to check whether the temperature increase 

at the collector can enable charging of the higher-priority storage tank.

Setting range: S2 or S3/default setting: S2

In systems with two storage tanks charging of the lower-priority storage tank 

will never take place until this set temperature setpoint at the storage tank 

sensor of the higher-priority storage tank is exceeded.

Setting range: from 0°C to 90°C/default setting: 40°C

10.10 Priority sensor  

menu 5.x

  = charging priority in systems with two 

storage tanks

10.12 Charging pause  

menu 5.x

  = interruption of charging

Settings   

menu 5

 

 

10

10

10. Settings (continued)

The  charging  of  the  lower-priority  storage  tank  is  interrupted  after  the 

settable time in order to check whether the collector can reach a temperature 

level that will soon enable charging in the higher-priority storage tank. If 

the conditions for charging the higher-priority storage tank or for continued 

interruption are not met, then the charging of the lower-priority storage tank 

is enabled again and interrupted again after the time set here in order to 

consider the current temperature increase of the collector.

 

Setting range: from 5 to 90 minutes/default setting: 10 minutes

For  precise  setting  of  the  charging  priorities  for  systems  with  multiple 

storage  tanks,  the  necessary  temperature  increase  of  the  collector  at 

which the interruption of the charging in the lower-priority storage tank is 

extended by one minute is set here. The interruption is extended because 

the temperature increase of the collector is expected to enable charging 

in  the  higher-priority  storage  tank  soon.  If  the  rise  in  temperature  falls 

below the set value, then the charging of the lower-priority storage tank 

is enabled again.

Setting range: from 1°C to 10°C/default setting: 3°C

10.11 T priority  

menu 5.x

  = temperature threshold for absolute priority

10.13 Increase  

menu 5.x

  = temperature increase during the charging pause

Содержание TDC 4





















































Отзывы: