Sorel HCC 6 Скачать руководство пользователя страница 25

25

Settings cooling

Settings cooling

This setting is used to determine the allowed overshoot of the 

fl

 ow temperature at sen-

sor S2 over the calculated reference 

fl

 ow temperature. If the measured temperature 

at S2 exceeds the reference temperature for the time period set inf 5.2.8, cooling is 
switched off.

Settings range: -10°C to 10°C / Default: 3°C

5.2.3. - On hysteresis

Slope of the charakteristik curve: Reference fl ow temperature

Changes the relation of room temperature and reference 

fl

 ow temperature  for the 

cooling mode. The higher this value, the colder the reference 

fl

 ow temperature.

Settings range: 1.0 to 10.0 / Default: 2.0

5.2.4. - Slope reference fl ow

 Room reference temperature in cooling mode
This temperature is the target temperature for the controlled room. The 

fl

 ow tempera-

ture is regulated accordingly.

Settings range: 15 to 30 / Default: 25

5.2.5. -  Room reference cooling

Minimum 

fl

 ow temperature in cooling mode

This is the lower limit of the 

fl

 ow reference temperature for cooling.

Einstellbereich: 5 °C bis 20 °C / Voreinstellung: 10 °C

5.2.6. - Min. fl ow cool

Maximum 

fl

 ow temperature in cooling mode.

This is the upper limit of the 

fl

 ow reference temperature for cooling.

Einstellbereich: 20 °C bis 40 °C / Voreinstellung: 25 °C

5.2.7. - Max. fl ow cool

Delay of cooling and additional heating

To prevent switching of additional heating or cooling when temperature 

fl

 uctuations oc-

cur, it is possible to delay the switching of the corresponding relay for up to 5 minutes. 
When the conditions are still met for the whole time, the relay is switched.

Settings range: 0 to 5 minutes / Default: 1 minute

5.2.8. - Delay

Delay applies to heating and cooling (see also „5.1.9. - Delay“ on page 23)

Caution

Yes:

 Cool down to Reference 

fl

 ow tempe off hysteresis („5.2.2. - Off hyster-

esis“ on page 24) measuring at 

fl

 ow sensor S2 and buffer S3.

No: 

Cool down to Reference 

fl

 ow tempe off hysteresis („5.2.2. - Off hysteresis“ 

on page 24) measuring at 

fl

 ow sensor S2, temperature at buffer S3 is ignored.

Settings range: Yes, No / Default: Yes

5.2.9. - Cool storage

Содержание HCC 6





































Отзывы: