Sony XDCAM PDW-HR1 Скачать руководство пользователя страница 167

Страница: 167 / 214

167

Maintenance Menu

Ch
apt

er 8

M46: MENU
DATA
CONTROL

M461: MENU
STATUS DISP

Displays the status of the menu bank where the current menu settings are stored.

M462: SAVE
MENU DATA

Select whether to temporarily back up (save) setup menu settings before operations such as
software upgrades.

PUSH SET knob:

Back up (save) the settings.

MENU button:

Return to next highest menu level without backing up.

M463: LOAD
MENU DATA

Select whether to restore (load) setting that were backed up (saved) with the “SAVE MENU
DATA” item.

PUSH SET knob:

Restore (load) the settings.

MENU button:

Return to the next highest menu level without restoring.

M47: SETUP BANK4

Select the bank to be stored in menu bank 4, or reset menu bank 4.

CURRENT TO BANK4:

Store the current menu settings in menu bank 4.

BANK1 TO BANK4:

Store the menu bank 1 settings in menu bank 4.

BANK2 TO BANK4:

Store the menu bank 2 settings in menu bank 4.

BANK3 TO BANK4:

Store the menu bank 3 settings in menu bank 4.

RESET BANK4:

Reset menu bank 4.

M48: AUTO RECALL

Select whether to recall settings automatically from a menu bank when the system is
powered on, and if so which menu bank to recall from.

off

: Do not recall settings from a menu bank.

from BANK1:

Recall settings from menu bank 1.

from BANK2:

Recall settings from menu bank 2.

from BANK3:

Recall settings from menu bank 3.

from BANK4:

Recall settings from menu bank 4.

M49: RESET ALL SETUP

Reset the current menu settings to the factory settings.

PUSH SET knob:

Reset.

MENU button:

Return to the next highest menu level without resetting.

Notes

• The system frequency setting is also cleared. If you execute this item, reset the system

frequency

(see page 42)

• Date and time settings are not cleared, but the time zone setting is cleared. After executing

this item, reset the time zone

(see page 42)

M5: NETWORK: Items relating to network settings

Item

Setting

M50: DHCP

Set whether to assign an IP address automatically with the DHCP server.

DISABLE:

Do not assign automatically.

ENABLE:

Assign automatically.

M51: IP ADDRESS PRESET

Set IP address.

192.168.001.010

Note

When DHCP is set to “ENABLE”, it is not possible to set the IP address.

M52: SUBNET MASK PRESET

Set the subnet mask.

255.255.255.000

Note

When DHCP is set to “ENABLE”, it is not possible to set the subnet mask.

M53: DEFAULT GATEWAY
PRESET

Set the default gateway.

000.000.000.000

Note

When DHCP is set to “ENABLE”, it is not possible to set the default gateway.

M54: LINK SPEED

Set the communications speed.

AUTO, 10Mbps, 100Mbps, 1000Mbps

M4: SETUP MAINTENANCE: Items relating to the setup menu

Item

Setting

Содержание XDCAM PDW-HR1























































































































































































































Результаты поиска

Содержание XDCAM PDW-HR1

Отзывы:

Sony XDCAM PDW-HR1, Руководство по эксплуатации, Страница: 167 / 214

Результаты поиска

Содержание XDCAM PDW-HR1

Отзывы: