Sony XDCAM PDW-HR1 Скачать руководство пользователя страница 162 | Manualshive

Страница: 162 / 214

Sony XDCAM PDW-HR1 Скачать руководство пользователя страница 162

162

Setup Menu

C

h

ap
te

r 8

M

enu

s

Extended menu operations

Operations in the extended menu are similar to operations
in the basic menu.
When the unit is shipped from the factory, it is set up to
display the extended menu. If you wish, you can hide the
extended menu by changing a setting in the maintenance
menu.

To hide the extended menu

Proceed as follows to use the maintenance menu.

1

Holding down the HOME button, press the MENU
button.

The maintenance menu appears on the video monitor
display.

965

IMAGE ENHANCER (INPUT UP
CONVERTER)

Set up the operation of the up converter image enhancer for SD input,
separately from the settings for playback (menu items 950 to 959).

Sub-item

1

ENH SETTING

pb:

While SD signals are input, make the behavior of the image

enhancer of the up-converter follow the settings for playback (menu
items 950 to 959) (Settings for sub-items 2 to 11 under menu item
965 become invalid).

input:

While SD signals are input, make the behavior of the image

enhancer of the up-converter follow the settings for sub-items 2 to 11
under menu item 965 (separate settings during input of SD signals
from those during playback).

2

CONVERT

Select the up-converter mode.

CROP:

Select the edge-crop mode.

L-BOX:

Select the letter box mode.

SQUE (SQUEZ):

Select the squeeze mode.

3

H CROP P

When sub-item UP CONVERTER MODE of menu item 965 is set to
“crop”, adjust the H-crop (horizontal crop) position for up converter output
in edge crop mode.

–120 to 0 to 120

4

L BOX P

When sub-item UP CONVERTER MODE of menu item 965 is set to “l-
box”, adjust the vertical location of the position where the picture is cut
out for up converter output in letter box mode.

–120 to 0 to 120

5

CNV PROC

Select the source picture to use in converting SD to HD.

FIEL (FIELD):

Use field pictures.

ADAP (ADAPT):

Frame or field is selected automatically.

6

DETAIL

Adjust the up-converter image enhancer. Set the sharpness of edge
enhancement.

0 to 40 to 7F

7

LIMITER

Adjust the up-converter image enhancer. Set the maximum detail level
added to emphasize the original signal.

0 to 20 to 3F

8

CRISP

Adjust the up-converter image enhancer. Set the threshold amplitude at
which low amplitude signals are not emphasized.

0 to 8 to F

9

DEPEND

Adjust the up-converter image enhancer. Set the luminance range for
edge enhancement.

0 to 8 to F

10

H DETL F

Adjust the up converter image enhancer. Set the center frequency and
frequency properties for edge enhancement.

3.2M:

3.2 MHz ±1.1 MHz

4.5M:

4.5 MHz ±1.4 MHz

5.0M:

5.0 MHz ±0.7 MHz

4.0M:

4.0 MHz ±2.0 MHz

11

HV RATIO

Adjust the up-converter image enhancer. Set the horizontal/vertical ratio
for edge enhancement.

0 to 3 to 7

Menu items in the 900s, relating to digital process (DIGITAL PROCESS)

Item number

Item name

Settings

«
...
160
161
162
163
164
...
»

Содержание XDCAM PDW-HR1























































































































































































































Отзывы:

Нет отзывов