![background image](http://html.mh-extra.com/html/sony/xdcam-pdw-hd1200/xdcam-pdw-hd1200_operation-manual_417494025.webp)
25
Rear Panel
Cha
pt
er 2
Name
s
an
d F
unc
tions
of
P
ar
ts
When the unit is shipped from the factory, audio signal
output is eight channels with no switching, and RP188
timecode output is set to on. You can change these settings
with setup menu item 828 SDI AUDIO OUTPUT
SELECT and setup menu item 920 SD-SDI H-ANC
CONTROL.
The output from the 2 (SUPER) connector can have
timecode, menu settings, alarm messages, and other text
information superimposed. To turn superimposition off,
set CHAR SEL on the HOME page of the function menu
to “OFF”.
See “Items in the extended menu” (page 121) for more
information.
See “Basic Operations of the Function Menu” (page 43)
for more information.
f
REMOTE(9P) (remote control 9-pin) connector
(D-sub 9-pin)
To control this unit from a controller or VTR supporting
the RS-422A Sony 9-pin VTR protocol, connect the device
to this connector.
g
DC IN 12V connector (XLR 4-pin, male)
Connect to a DC power source of 12 V.
When using the BKP-L551 Battery Adaptor to mount a
battery pack, connect the power cable of the BKP-L551.
For details, see “Supplying power” on page 27.
h
REMOTE connector (4-pin)
Supplies power to the RM-280 Editing Controller.
i
COMPOSITE OUTPUT 1, 2 (SUPER) (analog
composite video output 1, 2 (superimpose))
connectors (BNC type)
Output analog composite video signals. You can
superimpose timecodes, menu settings, or error messages
on the output of the 2 (SUPER) connector when CHAR
SEL on the HOME page of the function menu is set to ON.
See “Basic Operations of the Function Menu” on page 43
for more information about the CHAR SEL setting.
j
REF.VIDEO INPUT (reference video signal input)
connectors (BNC type)
The two connectors form a loop-through connection; when
a reference video signal is input to the left connector, the
same signal is input from the right connector (
) (IN)
to a connected device. When no connection is made to the
right connector, the left connector is automatically
terminated with an impedance of 75 ohms.
k
(network) connector (RJ-45 type)
This is a 10BASE-T/100BASE-TX/1000BASE-T
connector for network connection.
• For safety, do not connect the connector for peripheral
device wiring that might have excessive voltage to this
port. Follow the instructions for this port.
• When you connect the LAN cable of the unit to
peripheral device, use a shielded-type cable to prevent
malfunction due to radiation noise.
l
MAINTENANCE connectors
These are the USB connectors for maintenance.
Connect a Windows USB keyboard or mouse
, or a USB flash drive to access planning metadata
stored on the drive
.
1
Power supply section
a
POWER (main power) switch
Press the
:
side to power on the unit. Press the
a
side to
power off.
When using the unit, normally leave the POWER switch in
the
:
(on) position, and use the on/standby button on the
front panel to switch the unit between the operating state
and standby state.
Before turning the main power off, always check to be sure
that the unit is in the standby state, and then press the main
power switch to the
a
side.
b
-
AC IN connector
Connect to an AC power supply with the power cord (not
supplied).
2
Analog audio signal input/output section
CAUTION
Note
1
POWER switch
2
-
AC IN connector
ANALOG AUDIO INPUT
ANALOG AUDIO OUTPUT
1
2
1
2
AUDIO MONITOR
R
L
1
ANALOG AUDIO INPUT 1, 2 connectors
2
ANALOG AUDIO OUTPUT 1, 2
connectors
3
AUDIO MONITOR R, L connectors
Содержание XDCAM PDW-HD1200
Страница 1: ...PROFESSIONAL DISC RECORDER PDW HD1200 OPERATION MANUAL English 1st Edition Revised 1 ...
Страница 9: ...Table of Contents 9 Glossary 172 Index 174 ...
Страница 167: ...167 List of Supported USB Keyboards Appendix ...
Страница 178: ...Sony Corporation PDW HD1200 SYL 4 427 654 02 1 2012 ...