Sony UP-D70XR Скачать руководство пользователя страница 69

Страница: 69 / 96

4-19

UP-D70XR

RIBBON ERROR
Detection sensor : Take up FG sensor (Photo interrupter) and supply FG sensor (Photo interrupter)

Cause

: It was judged that ribbon is stopped by both FG sensors during beginning

detection of ribbon.

Symptom

: 1.

Ribbon is jammed.

Ribbon is cut at the halfway.

Paper or ribbon is stopped at the halfway.

Sensor defective

Take up ribbon motor does not operate.

Take up ribbon motor rotate slowly.

HEAD IN COOLING/HEAD IN HEATING

Detection sensor : Head thermistor
Cause

: Head temperature is less than 15

C or more than 60

Symptom

: 1.

Head temperature is over than possible printing temperature range (15 to 60

C).

Head thermistor defective

Head harness defective

g) HEAD CABLE NOT CONNECTED (This is not described in users manual.)

Detection sensor : Head thermistor

Cause

: Head temperature can not be measured.

Symptom

: 1.

Head thermistor defective

Head harness defective

Содержание UP-D70XR

































































































Результаты поиска

Содержание UP-D70XR

Отзывы:

Похожие инструкции для UP-D70XR

Бренды по названию

Популярные бренды

Sony UP-D70XR, Руководство по обслуживанию

Результаты поиска

Содержание UP-D70XR

Отзывы:

Похожие инструкции для UP-D70XR

Бренды по названию

Популярные бренды