Sony UP-D70XR Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 96

background image

1-6

UP-D70XR

10

Preparation

Connections

This section introduces the connections of the printer.
For detailed information on how to connect the printer to the UPA-D3 digital
image processor, read the instruction manual supplied with the UPA-D3.
For further details, contact your Sony dealer.

Connecting the Computer

The printer connects to either of the computer Windows or Macintosh via the
parallel interface. The printer can also connect to the Macintosh computer via the
SCSI interface.

Notes

• Be sure to connect one printer to one computer. Do not connect two computers to

the printer.

• Do not connect the computer equipped with the SCSI interface and parallel

interface to both of the PARALLEL DATA IN connecter and SCSI connecter of
the printer at the same time.

• Before connecting the cable, make sure to turn off the power switches on your

computer and any peripheral equipment.

• Grasp the connector at the end of the cable, and firmly insert it into the socket.
• The total length of the SCSI cabling used with a single-host computer should be

less than 6 meters.

• The parallel data cable should be less than 3 meters long and should conform to

Centronics specifications for printer cables.

• Avoid sending parallel data to the printer while the printer is processing SCSI

commands, and vice versa.

• Cable connection requirements vary depending on computers and peripherals.

For the details of your installation, please refer to the manuals for your computer
and peripherals.

When connecting a printer via the parallel interface

Parallel data cable
(shielded type)

11

Preparation

Note

If the printer is connected at the physical end of the SCSI bus, set the built-in
terminator to ON (on this page).

Installing the Printer Driver Program

The printer driver program should be installed before starting operation.
The instruction manual for the printer driver for the UP-D70A digital color printer
is stored on the CD-ROM supplied with the printer. Substitute this manual for the
printer driver manual for the UP-D70XR.
For detailed information, read the ReadMe file on the CD-ROM.

Setting the DIP Switch

The DIP switches on the rear panel of the printer determine the on/off state of the
internal SCSI bus terminator and the SCSI device ID number.
As shipped from the factory, the DIP switches are set up as follows:

Terminator ON/OFF setting

If printer is located at the physical end of the SCSI bus, this switch should be set to
ON. Otherwise, if another device is at the end of the bus, this switch should be
OFF.

When connecting a printer via the SCSI interface

SCSI cable (shielded type)
(50 pin full - 50 pin half pitch)

Switch

TERMINATOR

ON

The internal terminator is ON.

a)

OFF

The internal terminator is OFF.

ON 4 2 1

OFF 0 0 0

TERMINATOR

SCSI ID

(Factory setting)

a) Factory setting

«
...
10
11
12
13
14
...
»

Содержание UP-D70XR

































































































Отзывы:

Нет отзывов

Похожие инструкции для UP-D70XR

Бренд: Xerox Страницы: 73

Бренд: Xerox Страницы: 2

Бренд: Dascom Страницы: 138

Бренд: Dascom Страницы: 166

464de - X B/W Laser

Бренд: Lexmark Страницы: 27

Бренд: Cashino Страницы: 51

Бренд: BIXOLON Страницы: 59

ProJet x60 Series

Бренд: 3D Systems Страницы: 72

Бренд: Keithley Страницы: 97

Бренд: Agilent Technologies Страницы: 2

Бренд: Microcom Страницы: 207

Бренд: Xerox Страницы: 2

Бренд: Galileo Страницы: 15

Бренд: GeBe Страницы: 25

Бренд: Lexmark Страницы: 489

Бренд: Epson Страницы: 97

Бренд: Epson Страницы: 4

Бренд: Epson Страницы: 107

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды