Sony UP-D70XR Скачать руководство пользователя страница 91

Страница: 91 / 96

6-7

UP-D70XR

Printing operation is done, but nothing is printed.

Poor connection
of harness.

Check IC110 and
IC101 on SY-270 Board.

(Check V cont. )

YES

Is the harness inserted

to head correctly ?

Check CN201 A-

on FMY-15 Board.

Is power supply head

connector

through

than 17 V ?

When pulling

FMY-15 Board out, using only

IF-610 Board, is test pattern

printing normal?

YES

Is CN10

on SY-270 Board

more than 1.5 V?

Check Power
Supply.

YES

When pulling

IF-610 Board out, using only

FMY-15 Board, is test pattern

printing normal?

YES

Check CN101

on IF-610 Board.

Check head control block on
SY-270 Board refferring to timing
chart of SY-270 and MEC-11 Boards
operation description.

Check D/A
converter and CPU.

Содержание UP-D70XR

































































































Результаты поиска

Содержание UP-D70XR

Отзывы:

Похожие инструкции для UP-D70XR

Бренды по названию

Популярные бренды

Sony UP-D70XR, Руководство по обслуживанию

Результаты поиска

Содержание UP-D70XR

Отзывы:

Похожие инструкции для UP-D70XR

Бренды по названию

Популярные бренды