Sony TC-WE625 - Dual Auto Reverse Cassette, Руководство по эксплуатации

Страница: 8 / 92

8
EN
Advanced Playback Operations
3-862-713-31(1)/CED/SP
§
P R r
§
P R r
p
ª ·
0
g
)
PAUSE
CLEAR BACK FRONT
REC MUTE REC PAUSE REC MUTE REC
ON FILTER ON OFF
(AMS) (AMS) 0 ) (AMS) (AMS)
p
ª ·
– RMS +
RMS/START
MEMORY RESET MEMORY A B COUNTER
SET CHECK DISPLAY DECK A DECK B A+B REC HIGH/NORMAL
DOLBY NR
B C S
RMS AUTO CAL(START P ) DUBBING A B
START(DECK B P )
PITCH CONTROL
+ –
Ø
ON
ø
OFF
A a RELAY
DIRECTION MODE
AUTO REC LEVEL
FADER ARL
π SYNCHRO
PHONES
0
1
2
3
4
5
6
7
8
9
10
RESET
RESET MEMORY RESET
0 / ) 0 / ) ª / ·
Note
Check the direction indicator of the deck you use. When you
locate a track on the reverse side (when
ª
lights up), press
the button(s) in the parentheses.
Locating a Track (Multi-AMS/
Auto Play/Memory Play)
You can locate the following/previous tracks within a
range of 30 tracks (Multi-AMS: Automatic Music
Sensor) or the beginning of a tape quickly (Auto Play).
You can even locate a specific point anywhere on a
tape (Memory Play).
Notes
• The Multi-AMS function may not work correctly if:
— the blank space between tracks is less than 4 seconds
long.
— there is a passage of low frequencies or very low
volume within a track.
— the signal strength of the left and right channels are
very different.
• The Multi-AMS function is inoperative on a deck
whenever the other deck is playing, recording (except
during dubbing), or in pause.
• Even if DIRECTION MODE is set to a , the deck stops
when the current side reaches the end during Multi-AMS
operation.
• The tape counters are reset to “0.00” (TC-WE825S/WE725
only) or to “0000” (TC-WE625 only) when you turn off the
tape deck.
To locate
The beginning of the
current track
(Multi-AMS)
Press
The beginning of the
next or succeeding
tracks
(Multi-AMS)
)
(or
0
) as many times as you
want during playback.
For example, to locate 2 tracks
ahead, press twice.
0
(or
)
) once during playback.
0 (or ) ) as many times as you
want during playback.
For example, to locate 2 tracks
behind, press three times.
The beginning of the
preceding tracks
(Multi-AMS)
The beginning of a
tape (Auto Play) MEMORY on the deck being used
repeatedly until “M” disappears in
the display. Then press
0 (or ) )
while holding down
·
(or
ª
).
MEMORY on the deck being used
repeatedly until “M” appears in the
display. Find the point you want,
then press RESET to reset the tape
counter and to memorize the point.
To locate the memorized point and
start playback, press
0
(or
)
)
while holding down
·
(or
ª
).
(Press 0 or ) to stop at “0.00”
(TC-WE825S/WE725 only) or at
“0000” (TC-WE625 only). )
A particular point on a
tape (Memory Play)
Advanced Playback Operations
4/08-09_TC-WE825S.31(1)EN 8/19/98, 4:25 PM 8