Sony CDR-W66, Руководство по эксплуатации

Страница: 37 / 40

37
Miscellaneous
Troubleshooting
“TOC Reading” is displayed for a long time.
, Normally, 30 sec to 1 min is required to read
TOC information. This is not a malfunction.
, The CD recorder reads CD-text-compatible
characters. Consequently, it takes longer
compared with players that are not CD-text-
compatible.
, Is the disc inserted upside-down?
, Is the disc’s recording surface dirty? (Refer to
page 34, “Precaution”.)
, Depending on the disc, you may need to remove
it and reinsert it for the disc to operate correctly.
After “TOC Reading” has been displayed, “OPC
Adjust” is displayed.
, With CD-R/RW discs, laser power may need to
be adjusted (OPC Adjust) when the disc is
inserted for the first time, whether it is new or
has been previously recorded. In this case, OPC
adjust lasts for approximately 40 s.
“No Disc” is displayed, even with a disc
inserted.
, Check that the disc is properly inserted between
the guides.(refer to page 34, “Disc Handling
Precautions”.)
Cannot play disc
, Is there anything recorded on the inserted disc?
, Check that the disc is a music disc. (not a CD-
ROM, etc.)
, Condensation (water droplets inside the CD
recorder) must be considered. Remove the disc,
and leave the CD recorder to stand with the
power supply turned ON for 1 hour, and then
turn OFF the power supply and ON again
before trying to play the disc again. (Refer to
page 34, “Condensation”.)
Cannot record to disc
, Is a play-only music CD inserted?
, Has the CD-R/CD-RW disc been finalized?
(Refer to page 9.)
, Are there already 99 tracks recorded on the disc?
(Refer to page 11, “Recording Precautions”.)
, Is the Recordable space on the disc full? (Refer
to page 11, “Recording Precautions”.)
, Is the source device connected correctly? (Refer
to page 5, “Connections”.)
, Is the INPUT switch selection correct? (Refer to
page 10, “Recording on a disc”.)
, Is the recording level set too low? (Refer to page
12, “Adjusting the Recording Level”.)
The recorded data does not stay on the disc.
, If the power supply is turned OFF during
recording or while PMA Writing is displayed,
writing to the PMA area will be incorrect, and
the recording disabled. (Refer to page 11,
“Rcording Precautions”.)
Cannot add track numbers, even pressing the
z (REC) button during recording.
, Check if auto track marking is ON (L.SYNC is
lit). (Refer to page 12, “Making Track Numbers
While Recording (Track Marking)”.)
Cannot play recorded discs on other CD
players.
, Has the disc been finalized? (Refer to page 18,
“Finalizing (FINALIZE)”.)
, Is the disc dirty or damaged? (Refer to page 34,
“Instaiiation Precautions”.)
, Even if the CD-RW disc is finalized, a CD-RW
disc cannot be played on a CD player that is not
CD-RW-compatible. (Refer to page 9,
“Finalizing”.)
, Be noted that in CD players there are some
models that are unable to play back a CD-R
disc.
Even though the parameters have been set,
the limiter and equalizer effects are not
operating.
, Set the SBM/LIMITER/EQ switch to LIMITER
+ EQ or SBM + L EQ. (Refer to page
15, “Using the Digital Limiter and Digital
Equalizer”.)
, Limiter or Equalizer becomes effective when
recording analog input signals or AES/EBU
digital input.
Contrary to this, ineffective at playing back, or
at recording digital input signals (Refer to page
15,“ Digital Equalizer Setting”.)
, SBM is very delicate, so if monitoring using
headphones, depending on your system, the
effects may not be recognizable.
Cannot use the remote for operations.
, Have the remote’s batteries worn down? (Refer
to page 5, “Inserting Batteries into the Remote”.)
Can’t operate using Remote Controller (when
for use as a wireless remote control)
, Isn’t an obstacle between the remote controller
and set ?
, Is the remote controller correctly directed
against the side laser reception of the set?
, Isn’t a connection cord for use of connecting
Control S connected either to remote controller,
or to the set?
The disc name and track name that were
entered have been erased.
, If the power supply is turned OFF or the disc
removed before being finalized, the entered
names will be erased. (Refer to page 18,
“Finalizing”.)
Miscellaneous