background image

 

MACHINE MOTION CONTROL -

 

Single lever, multi-

directional & continuously variable, controls 
direction of motion & speed of motion. Forward 
displacement of control produces forward motion. 
Rearward displacement of control produces 
rearward motion. Increased control displacement 
produces increased speed of motion. 

MOWER BLADE CONTROL 
SWITCH - Pull switch up 
(ON) to engage blade. 
Push switch down (OFF) to 
disengage blade.  
 
IMPORTANT: Mower Blade 
Control Switch must be in 
(OFF) disengaged position 
to start engine.

 

SYMBOLS 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

 

 
 
 
 
 
 
 
 
 

 

 
 

 

Hearing protection 
required during 
machine operation. 

 

Sound Power Level 
produced by machine and 
cutter deck - Lwa 105. 

PARKING BRAKE CONTROL 
LEVER

 

- Push control 

forward to disengage (un-
lock/off). 
Pull control rearward to 
engage (lock/on). 
 
IMPORTANT: Parking Brake 
must be engaged (locked) to 
start engine. 

 

ENGINE 
GLOW PLUG 
PRE-HEAT 

ENGINE

 

STOP

 

(OFF) 

ENGINE 
RUN (ON) 

ENGINE 
START 

Содержание EZF2100DKU, EZF2300GKU, EZF520

































Отзывы: