background image

 

18 

Section 3 - MAINTENANCE  

 

3.6 DECK 

REMOVAL 

 

(Continued From Previous Page) 
4.
 

Rotate spring loaded hitch latch pins 

(Located on both hitch plates) to the unlatched 
position. See Figure 3.10. 
5.  Move deck lift switch as if to lower deck and 
the lift arm will move up in the hitch plates. The 
lift arm needs to be high enough to clear the 
hitch plates when power unit is driven 
backward away from mower deck. See Figure 
3.9. 
6.  Pull lock collar back and slide power 
transfer shaft away from power take off (PTO) 
shaft. See Figure 3.11. 
7.  Disconnect wiring harness from mower deck. 
8.  Start power unit. Disengage parking brake. 
Carefully move power unit backward away from 
mower deck. 

 

FIGURE 3.10 

 

 

FIGURE 3.11 

 

3.7 

POWER TRANSFER SHAFT REMOVAL 
Engage parking brake. Turn engine “OFF” and 
remove key. The power transfer shaft connects 
the power unit to the mower deck. The shaft is 
telescoping for easy removal. Slide locking collar 
back toward mower deck and shaft will slide off. 
See Figure 3.11. 

 
 
 

WARNING 

DO NOT attempt any maintenance, adjustments or 
service with engine running. STOP engine. STOP 
blades. Set brake. Remove key. Remove spark plug 
wires and secure away from spark plugs. Engine 
and components are HOT. Avoid serious burns, 
allow sufficient time for all parts to cool. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

NOTE: DECK LIFT ARM SHOWN REMOVED FOR 
CLARITY. DECK WOULD NOT BE REMOVED AT THIS 
TIME IN DECK REMOVAL PROCEDURE. 

HITCH LATCH PIN SHOWN IN 
UNLATCHED POSITION 

HITCH 
PLATE 

POWER 
TRANSFER 
SHAFT 

LOCK COLLAR 

PULL LOCK 
COLLAR 
BACKWARDS 

POWER 
TAKE OFF 
SHAFT 

Содержание EZF2100DKU, EZF2300GKU, EZF520

































Отзывы: