background image

 

11 

Section 2 - OPERATING INSTRUCTIONS 

 
2.2.1.  STARTING ENGINE (Continued from previous page) 

 

FIGURE 2.6 

 

6.  IMPORTANT: (Diesel Engine Only) Use the 
Glow Plug only if engine is cold or outside 
temperature is cold. Rotate key counter 
clockwise to the preheat position (GL letter 
designation on switch) to allow the glow lamp to 
heat up. Hold key in the Glow Plug position for a 
maximum of 5 seconds See Figure 2.7. 
7.  Rotate key clockwise to the start position until 
engine starts. See Figure 2.7. 

NOTE:  If after 5 seconds of cranking the engine does 
not start, release the key and attempt starting again after 
waiting for approximately 20 seconds. 
 

 

FIGURE 2.7 

8.  After engine starts, allow a brief warm-up until 
engine runs smooth.  

 
2.2 

STOPPING - ENGINE  

2.2.1. ENGINE 

1.  Stop engine by turning key to the  “OFF” 
position. Move engine speed control to turtle 
“SLOW” position and key to “STOP” position. 
See Figure 2.7. 

 

WARNING 

DO NOT leave machine with engine running. STOP 
blades. STOP engine. Set brake. Remove key. 

 
2.2.2.  STARTING MOWER BLADES 

1. With engine running, move engine speed 
control to the Rabbit or “fast” position. 
2. Pull the blade switch out into the “ON” 
position to engage the mower blades. 
3.  Release the parking brake. 
4.  Move joystick carefully in the desired direction to 
propel the machine. A small movement of the 
joystick can cause the machine to move instantly. 
Move joystick carefully and slowly.  

 

WARNING 

DO NOT operate blades in reverse. STOP BLADES. 
LOOK and SEE behind and down for children, pets 
and hazards before and while backing. 

 
2.2.3.  STOPPING MOWER BLADES 

1.  Push the blade switch in to “OFF” position to 
disengage or stop the mower blades. See Figure 
2.2.  

 

WARNING 

Once blades are disengaged, they should come to a 
complete stop in 7 seconds. If the blades continue to 
rotate after 7 seconds, the electric clutch should be 
checked. Replacement of electric clutch may be 
necessary. Return the machine to an authorized 
Snapper dealer for replacement. DO NOT CONTINUE 
to operate mower if blades fail to stop in 7 seconds. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

FAST ENGINE 
SPEED POSITION 

SLOW ENGINE 
SPEED POSITION 

ENGINE SPEED CONTROL 
SHOWN IN “FAST” POSITION 

GLOW PLUG 

PRE-HEAT 

GL 

OFF 

ON 

ST 

STOP 

POSITION 

RUN 

POSITION 

START 

POSITION 

GAS ENGINE SWITCH POSITION 

DIESEL ENGINE SWITCH POSITION 

OFF 

ON 

ST 

START 

POSITION 

RUN 

POSITION 

STOP 

POSITION 

Содержание EZF2100DKU, EZF2300GKU, EZF520

































Отзывы: