background image

 

15 

Section 3 - MAINTENANCE 

 

3.2.3.  CHECK MOWER DRIVE BELT 

1.  Drive Belt Cover Removal 

a.  Lower deck to lowest setting. 
b. Remove knobs that secure the deck 
cover. See Figure 3.3. 
c.  Remove cover to gain access to deck belt. 

 

 

FIGURE 3.3 

 

2.  Checking Belt Tension 
The idler and spring provide proper belt tension 
and require no adjustment. If belt is frayed, slit, 
severed or belt strands exposed, replace belt 
before operating mower. 

 

3.3 

AFTER EVERY 25 OPERATING HOURS 

3.3.1. ENGINE 

1. Engine Oil 
Change engine oil. Refer to Section “CHANGE 
ENGINE OIL”. Refer to engine owner’s manual 
for oil specifications. 
2. Air Filter 
Refer to engine owner’s manual for service 
instructions. 
3.  Radiator - SEE WARNING 

a.  Clean radiator debris screen and cooling 
fins thoroughly. Refer to engine owner’s 
manual for service instructions. 
b.  Check coolant level in reserve tank. 

 

3.3.2. MOWER 

COMPONENTS 

1.  Mower Drive Belt 
No adjustment required. Replace belt as 
needed. 
2. Mower Blade 
Check blade for sharpness, wear, damage, and 
torque. Refer to Section “MOWER BLADE 
REPLACEMENT”. 
 
 
 
 
 

3.  Mower Deck Levelness 
Check mower deck for proper levelness.  Adjust 
as required. Refer to Section “MOWER DECK 
ADJUSTMENT – LEVELNESS”. 
 
4.  Cleaning Mower Deck 

a.  Remove key from ignition switch. 
b. Remove spark plug wire(s) and secure 
away from spark plug(s). GAS ENGINE 
ONLY. 
c.  Raise mower deck to its highest setting. It 
may be necessary to raise mower deck 
higher using a hydraulic floor jack. Secure 
deck with safety blocks. 
d.  Clean underside of mower deck, removing 
all accumulation of grass clippings and 
debris. 
e. Clean top of deck, removing all grass 
clippings and debris. 
 

5.  Mower Blade Spindle - Lubrication 

a. Remove four knobs that secure the deck 
cover. 
b. 

Remove cover to gain access to 

lubrication fitting located on the top of deck 
below deck pulleys. Lubricate with Kendall 
NLGI No. 2 lithium grease or equivalent, from 
a grease gun until grease purges from vent 
located on spindle housing underneath deck. 
See Figure 3.4. 

 

FIGURE 3.4 

 

6.  Mower Deck Linkage - Lubrication 

Lubricate all mower deck linkage pivot points 
with a light coat of motor oil. 
 

WARNING 

DO NOT remove cap from radiator when engine and 
coolant are hot. Coolant is pressurized. Severe 
burns could result.
 

REMOVE 
FOUR 
KNOBS 

REMOVE 
DECK COVER 

DECK PULLEYS 

LUBRICATE 
SPINDLE 
ASSEMBLIES 

Содержание EZF2100DKU, EZF2300GKU, EZF520

































Отзывы: