Smiths BOEING B737-100 Скачать руководство пользователя страница 98 | Manualshive

Страница: 98 / 146

background image

Smiths Aerospace

Electronic Systems – Malvern

DOC NO.0134ED

MAINTENANCE MANUAL SUPPLEMENT

BOEING B737-100/200/300/400/500

28-41-04

b) Adapter cable – 50 ohm, with BNC plug (Amphenol 31-202) to connect to the Hi-Z

receptacle on the test unit and a BNC receptacle (AMP 330885) to connect to the tee
connector.

(c) Ground cable

(3) TSU jumper harness:

(a) Part number 201475-001 (Smiths Aerospace Inc.)

B. References

(1) AMM 24-22-00/201, Manual Control

(2) AMM 27-81-00/201, Leading Edge Flaps and Slats

(3) AMM 28-23-00/201, Defueling

(4) AMM 28-41-81/401, Fuel Summation Unit

C. Access

(1) Location Zones

101

Control Cabin, Left

217

Right Main Wheel Well

303

Left Wing Inboard Leading Edge

402

Right Wing Outboard Leading Edge

403

Right Wing Inboard Leading Edge

(2) Access Panels

6540

Refueling Station Access Door

D. Prepare for the System Test

(1) Connect the external electrical power (Ref 24-22-00/201).

WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF THE LE AND

TE FLAPS AND FLAP DRIVE MECHANISMS BEFORE YOU MOVE THE FLAP
CONTROL LEVER. WITH HYDRAULIC POWER REMOVED, THE FLAPS WILL
MOVE AUTOMATICALLY BY ELECTRICAL POWER WHEN YOU MOVE THE
FLAP CONTROL LEVER. THIS CAN CAUSE INJURY TO PERSON OR DAMAGE
TO EQUIPMENT.

(2) Extend the leading edge flaps (Ref 27-81-00/201).

WARNING: YOU MUST CAREFULLY DO THE STEPS IN THE TASK BELOW TO INSTALL

THE LE FLAP SAFETY LOCKS. THE LE FLAPS CAN MOVE QUICKLY IF YOU
DO NOT INSTALL THE SAFETY LOCKS CORRECTLY. THIS CAN CAUSE
INJURY TO PERSON OR DAMAGE TO EQUIPMENT.

(3) Install the locks on the leading edge flaps (Ref 27-81-00/201).

(4) Remove all the fuel from the fuel tank and the fuel in the sumps (Ref 28-23-00/201).

EFFECTIVITY

NOTE:

If you do an adjustment of only one tank system, you can move the fuel into the other
tanks.

CONFIG

4.2

Page 504

Dec 18/02

Airplanes with Smiths 2307 Model Fuel Quantity Indicators
with TSU

(SIMMONDS SYSTEM TESTER)

«
...
96
97
98
99
100
...
»

Содержание BOEING B737-100



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для BOEING B737-100

Бренд: Bacharach Страницы: 64

Surface Scatter 7 sc

Бренд: Hach Страницы: 6

Бренд: Hach Страницы: 118

Бренд: Hach Страницы: 388

Orbisphere 51 Series

Бренд: Hach Страницы: 118

ORBISPHERE 3650 Atex

Бренд: Hach Страницы: 51

Бренд: Hach Страницы: 72

POLYMETRON 8362

Бренд: Hach Страницы: 78

Pocket Colorimeter II

Бренд: HACH LANGE Страницы: 146

Бренд: Hach Страницы: 146

Бренд: Hach Страницы: 36

PHOSPHAX indoor sc

Бренд: Hach Страницы: 104

Lange ORBISPHERE 3100

Бренд: Hach Страницы: 384

Бренд: Hach Страницы: 172

Бренд: Magnum Energy Страницы: 3

Kotron 805 series

Бренд: Magnetrol Страницы: 36

Бренд: Magnescale Страницы: 104

Бренд: Magnescale Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды