Doc. no.IZ
＊
-OMV0005
9
1. How to Order
1-1.Ionizer body
◎
Cautions when using the IZN10E-11
□□□
-
□
(Female threads for piping)
For the female threads (Rc1/8), either a Made-to-Order
nozzle or a fitting/tubing combination must be prepared and
connected by the user.
If a nozzle with an outlet port or I.D. of less than 4 mm is
connected, the air pressure in the nozzle may increase,
depending on the configuration.
The product uses a high frequency AC voltage. If the air
pressure at the emitter increases during ion generation, the
efficiency decreases and the maintenance alarm (signal
output, maintenance LED) will be activated (refer to the
figure to the right).
Neutralizing performance is low when the maintenance
alarm is generated.
The table below shows the supply pressure specifications
when a Made-to-Order nozzle or fitting/tubing combination are connected.
Made-to-Order nozzle product names / Piping examples
Made-to-Order nozzle
product number
Supply pressure
specifications
Circular diffusion nozzle
IZN10-G-X198
0.05 to 0.1 MPa
Flat diffusion nozzle
IZN10-G-X199
0.05 to 0.1 MPa
Bar nozzle (straight type)
IZN10-G-
□
-X216
0.05 to 0.1 MPa
Circumferential jet bar nozzle (straight type)
IZN10-G-X278
0.05 to 0.15 MPa
Bender tube nozzle
IZN10-G-
□
-X205
0.05 to 0.15 MPa
Long nozzle
IZN10-G-
□
-X226
0.05 to 0.15 MPa
Fitting (Applicable tube O.D. 6 mm) + Tube (O.D. 6 mm, I.D. 4 mm)
Note 1)
-
0.05 to 0.1 MPa
Fitting (Applicable tube O.D. 8 mm) + Tube (O.D. 8 mm, I.D. 5 mm)
Note 1)
-
0.05 to 0.3 MPa
Note 1) When connecting the tubing, use a length of tubing less than 500 mm for the connection, regardless of
the inside diameter size.
When using piping materials prepared by the user, secure a sectional area of 4 mm inside diameter. If using
tubing, check the minimum bending radius and keep the tube length 500 mm or less.
Do not receive a moment force on the nozzle (Page 6).
IZN10Ｅ - 01
P
06
Z - B1
High frequency AC nozzle type
Made to Order
Nozzle type
Bracket
Symbol
Type
Symbol
Type
01
Energy saving nozzle
Nil
Without bracket
02
High flow rate nozzle
B1
With L-bracket
11
Female threads for piping (Rc1/8)
B2
With pivoting bracket
B3
With DIN rail mounting bracket
Input / Output specifications
Power supply cable
Symbol
Type
Symbol
Type
Nil
NPN Input / Output
Nil
With power supply cable (3m)
P
PNP Input / Output
Z
With power supply cable (10m)
N
Without power supply cable
One-touch fitting
Symbol
Type
06
ø6 : Metric size
07
ø6.35
（
1/4"
）
: inch size
16
ø6 : Metric size (elbow)
17
ø6.35
（
1/4"
）
: inch size (elbow)
-
Female threads for piping (cross section)
Ionized air
Nozzle / Fitting
Female threads
for piping
Around
the emitter
Compressed air
Emitter
