manualshive.com logo in svg

SMC Networks ISE30A Series, Руководство по эксплуатации

Поделиться
Скачать
SMC Networks ISE30A Series Скачать руководство пользователя страница 6

 

-5- 

 

No.PS##-OML0003-B 

 

 

■

NOTE

 

○

Follow the instructions given below when designing, selecting and handling the product. 

●

The instructions on design and selection (installation, wiring, environment, adjustment, operation, 

maintenance, etc.) described below must also be followed. 

*Product specifications 

•

The direct current power supply to combine should be UL approved as follows. 

Circuit (of Class2) which is of maximum 30 Vrms (42.4 V peak) or less, with UL1310 Class2 power supply unit or 
UL1585 Class2 transformer. 

•

The Pressure switch is a 

  approved product only if it has a 

  mark on the body. 

•

Use the specified voltage. 

Otherwise failure or malfunction can result. 

•

Do not exceed the specified maximum allowable load. 

Otherwise it can cause damage or shorten the lifetime of the Pressure switch. 

•

Design the product to prevent reverse current when the circuit is opened or the product is forced to operate for 

operational check. 

Reverse current can cause malfunction or damage to the product. 

•

Input data to the Pressure switch is not deleted, even if the power supply is cut off. 

(Writing time: 1,000,000 times, Data duration: 10 years after power off) 

•

For the details of compressed air quality, refer to ISO 8573-1, 1.1.2 to 1.6.2: 2001. 

This can cause operating failure. 
If compressed air containing condensate is used, install an air dryer or drain catch before the filter and perform 
drainage regularly. 
If drainage is not performed regularly and condensate enters the secondary side, it can cause operating failure of 
pneumatic equipment. 
If regular drainage is difficult, the use of a filter with an auto drain is recommended. 

•

Applicable fluid is air, inert gases and incombustible gases. 

Do not use a fluid containing chemicals, synthetic oils including organic solvent, salt and corrosive gases. 
Otherwise, damage to the product and malfunction can result. 
Check the details of the specifications before using. 

•

Use the specified measurement flow rate and operating pressure. 

Otherwise it can cause damage to the pressure switch or inability to measure correctly. 

•

Reserve a space for maintenance. 

Allow sufficient space for maintenance when designing the system. 
 

●

Product handling 

*Installation 

•

Tighten to the specified tightening torque. 

If the tightening torque is exceeded the mounting screws and brackets may be broken. 
If the tightening torque is insufficient, the product can be displaced and loosen the mounting screws. 
(Refer to "Mounting and Installation" on page 14.) 

•

Do not apply excessive stress to the product when it is mounted with a panel mount. 

Otherwise damage to the product and disconnection from the panel mount can result. 

•

Be sure to ground terminal FG when using a commercially available switch-mode power supply. 

•

Do not drop, hit or apply shock to the Pressure switch. 

Otherwise damage to the internal parts can result, causing malfunction. 

Содержание ISE30A Series



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды