SMC Networks ISE30A Series Скачать руководство пользователя страница 41

Страница: 41 / 66

-40-

No.PS##-OML0003-B

Press the

button to start copying.

The master Pressure switch

The slave Pressure switch

Sending/

Receiving

Copy

completed

(Red)

(Green)

Press the

button.

When completing copy function,
press the

and

buttons

simultaneously for 1 second or longer. Setting of [F97] copy function completed

∗

: If the copy to the slave pressure switch is not completed, it is detected as a copying function sending/receiving error.

Press the

and

buttons simultaneously for 1 second or longer to return to measurement mode. Then, check the wiring and

specifications of the switch and retry copy function.

The copy can be done continuously and
the copy ready statues can be held even
if the power supply is turned off.

Press the

and

buttons simultaneously
for 1 second or longer.

Press the

button.

Flashing

(Red)

Flashing

(Green)

The copy ready status is held even if the power
supply is turned off.

Содержание ISE30A Series



































































Результаты поиска

Содержание ISE30A Series

Отзывы:

Бренды по названию

Популярные бренды

SMC Networks ISE30A Series, Руководство по эксплуатации

Результаты поиска

Содержание ISE30A Series

Отзывы:

Бренды по названию

Популярные бренды