SMC Networks ISE30A Series Скачать руководство пользователя страница 58

Страница: 58 / 66

-57-

No.PS##-OML0003-B

Specification

■

Specifications

Model No.

ZSE30A

(For vacuum)

ZSE30AF

(For compound)

ISE30A

(For positive pressure)

Rated pressure range

0.0 to -101.0 kPa

-100.0 to 100.0 kPa

-0.100 to 1.000 MPa

Set pressure range

10.0 to -105.0 kPa

-105.0 to 105.0 kPa

-0.105 to 1.050 MPa

Withstand pressure

500 kPa

1.5 MPa

Min. display unit

0.1 kPa

0.001 MPa

Applicable fluid

Air, inert gases and incombustible gases

Power supply voltage

12 to 24 VDC ±10%, ripple (p-p) 10% or less (Protected against inverse connection)

Current consumption

40 mA or less

Switch output

NPN or PNP open collector output 1 output

NPN or PNP open collector output 2 outputs (selectable)

Max. load current

80 mA

Max. applied voltage

28 V (NPN output)

Residual voltage

1 V or less (at 80 mA load current)

Response time

2.5 ms or less

(Chattering-proof function working: 20, 100, 500, 1000 or 2000 ms selected)

Short circuit protection

Provided

Repeatability

±0.2%F.S. ±1 digit

Hysteresis mode

Hys
teresis Window comparator mode

0 to variable

∗

Output Voltage
(rated pressure range)

1 to 5 V ±2.5%F.S.

0.6 to 5 V

±2.5%F.S.

Linearity ±1%F.S.

Voltage
output

∗

Output impedance

Approx. 1 k

Ω

Output current
(rated pressure range)

4 to 20 mA ±2.5%F.S.

2.4 to 20 mA

±2.5%F.S.

Linearity ±1%F.S.

Analog
output

Current
output

∗

Load impedance

Max. load impedance: 300

Ω

(at power supply voltage of 12 VDC)

600

Ω

(at power supply voltage of 24 VDC)

Min. load impedance: 50

Ω

Display method

4 digits 7-segment display, Dual-color display (red/green)

Indicator accuracy

±2%F.S. ±1digit (at ambient temperature 25±3

Indication light

Light when ON OUT1: Green OUT2: Red

Enclosure IP40
Ambient temperature range

Operation: 0 to 50

C, Storage: -10 to 60

C (No condensation or freezing)

Ambient humidity range

Operation, Storage: 35 to 85%RH (No condensation)

Withstand voltage

1000 VAC, 1 minute Between lead block and case

Environ
ment

Insulation resistance

50 M

Ω

or more at 500 VDC Between lead block and case

Temperature characteristic

±2%F.S. (25

C reference)

Lead wire

Oil resistance vinyl cabtyre cable

3 cores

3.5, 2 m

4 cores Sectional area of conductor: 0.15 mm

(AWG26)

Outside diameter of insulator: 1.0 mm

Standard

CE, UL/CSA, RoHS

∗

1: If the applied voltage fluctuates around the set value, the hysteresis more than the fluctuating width needs to be set. Otherwise,

chattering will occur.

∗

2: If analog voltage output is selected, the analog current output cannot be selected at the same time.

∗

3: If analog current output is selected, the analog voltage output cannot be selected at the same time.

Содержание ISE30A Series



































































Результаты поиска

Содержание ISE30A Series

Отзывы:

Бренды по названию

Популярные бренды

SMC Networks ISE30A Series, Руководство по эксплуатации

Результаты поиска

Содержание ISE30A Series

Отзывы:

Бренды по названию

Популярные бренды