SMC Networks ISE30A Series Скачать руководство пользователя страница 31

Страница: 31 / 66

-30-

No.PS##-OML0003-B

■

[F 2] Setting of OUT2

Set output method of OUT2.
Display color depends on OUT1 output, and is not set with this function.

<Operation>

Press the

button in function selection mode to display [F 2].

Press the

button

Moves on to setting of output mode

Set based on [F 1] setting of OUT1 (page 27 to 29).

∗

: If the output specification is 1 output or analog output specification is used, the display shows [---], and this function cannot be

set.

■

[F 3] Setting of response time

Select the response time of the switch output.
Output chattering is prevented by setting the response time.

<Operation>

Press the

button in function selection mode to display [F 3].

Press the

button.

Move on to setting of response time.

Press the

button to set.

Return to function selection mode.

Setting of [F 3] response time completed

Setting of response time

Press the

button to select response time.

Содержание ISE30A Series



































































Результаты поиска

Содержание ISE30A Series

Отзывы:

Бренды по названию

Популярные бренды

SMC Networks ISE30A Series, Руководство по эксплуатации

Результаты поиска

Содержание ISE30A Series

Отзывы:

Бренды по названию

Популярные бренды