SMC Networks ISE30A Series Скачать руководство пользователя страница 38

Страница: 38 / 66

-37-

No.PS##-OML0003-B

■

Special function setting

■

[F90] Setting of all functions

All functions can be set in series.
This function is equipped with existing models as well.

<Operation>

Press the

button in function selection mode to display [F90].

Press the

button.

Move on to setting of all functions.

[on] (used) selected

Setting of each function

∗

[oFF] (unused)
selected.

Press the

button

to set.

Return to function
selection mode.

After the change to [oFF] (unused),

press the

button to set.

Return to function selection mode.

Press the

button for 2
seconds or longer.

[F90] setting of all functions completed

Measurement mode

∗

1: Setting of functions

Every time

button is pressed, function turns to page 38.

Set by

button.

Refer each paragraph for the detail of setting.

Setting of all functions

Press the

button to select all functions.

Содержание ISE30A Series



































































Результаты поиска

Содержание ISE30A Series

Отзывы:

Бренды по названию

Популярные бренды

SMC Networks ISE30A Series, Руководство по эксплуатации

Результаты поиска

Содержание ISE30A Series

Отзывы:

Бренды по названию

Популярные бренды