SMC Networks ISE30A Series Скачать руководство пользователя страница 56

Страница: 56 / 66

-55-

No.PS##-OML0003-B

Reference

No.

Problem

Possible cause

Investigation method

Countermeasure

Incorrect wiring

(1) Check the connection at FUNC

terminal.

Check the power supply wiring.

(2) Check the length of lead wire.

(1) Correct the wiring.
(2) The maximum

transmitting distance of
the copy function is 4 m.

Shorten the lead wire to
4 m or less.

Improper model

The models of the master Pressure
switch and the slave Pressure switch
are different from each other.

Check the models.
Copying is available when
the pressure range, output
specification and unit
specification are identical.

Error in
connected
product
numbers

Check the number of connected
slave Pressure switches.

The number of connected
products with which copying
at a time is possible is up to
10 pcs.
Reduce the number to
10 pcs or less.

Slave Pressure
switch does not
complete
copying.

Product failure

Replace the product.

Effect of
pressure source
fluctuation due
to small
hysteresis or too
early of a
response time

(1) Check the set pressure

(hysteresis)

(2) Check the response time

(1) Check the pressure

setting.

(2) Reset the setting of

function.

Incorrect wiring/
lead wire
breakage

(1) Check the power supply wiring.
(2) Check if bending stress is applied

to a specific part of the lead wire.

(bending radius and tensile force
applied to the lead wire)

(1) Correct the wiring
(2) Correct the wiring

conditions. (Adjust the
tensile force and widen
the bending radius.)

The operation is
unstable.
(Chattering)

Product failure

Replace the product.

Содержание ISE30A Series



































































Результаты поиска

Содержание ISE30A Series

Отзывы:

Бренды по названию

Популярные бренды

SMC Networks ISE30A Series, Руководство по эксплуатации

Результаты поиска

Содержание ISE30A Series

Отзывы:

Бренды по названию

Популярные бренды