Smartgen HGMS61 Скачать руководство пользователя страница 18

Страница: 18 / 47

HGMS61 Genset Controller User Manual Page 18 of 47

No.

Function

Cable

Size

Description

is recommended. No.16 controller inside has been
connected to B-.

17 RS485-

0.5mm

Impedance-120Ω shielding wire is recommended, its

single-end connect with ground.

18 RS485+

0.5mm

19 Fuel Relay Output

1.5mm

B+ is supplied by 21 points, rated 10A.

Relay specification: DC 24V.

20 Start Relay Output

1.5mm

21 DC input B+

2.5mm

Connect to start battery positive post, 32A fuse is
used in controller.

22 DC input B-

2.5mm

Connect to battery negative post.

23 ACT1

2.5mm

Connect to external executor. The terminal in
controller is connected to Terminal 10 of Connector
B.

24 ACT2

2.5mm

Connect to external executor. The terminal in
controller is connected to Terminal 7 of Connector B.

25 CB+

2.5mm

Connect to external start battery positive post. The
terminal in controller is connected to Terminal 1 of
Connector B.

26 CB-

2.5mm

Connect to external start battery negative post. The
terminal in controller is connected to Terminal 2 of
Connector B.

CT A Phase Monitoring
Input

1.5mm

Externally connect to CT secondary coil. (Rated
5A)

CT B Phase Monitoring
Input

1.5mm

Externally connect to CT secondary coil. (Rated
5A)

CT C Phase Monitoring
Input

1.5mm

Externally connect to CT secondary coil. (Rated
5A)

30 CT Sensor Common

1.5mm

Refer to installation instructions.

31 UOUTPUT

1.0mm

Generator U-phase monitoring input will output after
the fuse.

Generator

U-phase

Voltage

Monitoring

Input

1.0mm

Connect to genset output U-phase, the control uses
10A fuse.

Generator

V-phase

Voltage

Monitoring

Input

1.0mm

Connect to genset output V-phase, the control uses
10A fuse.

Generator

W-phase

Voltage

Monitoring

Input

1.0mm

Connect to genset output W-phase, the control uses
10A fuse.

35 Genset N1 Wire Input

1.0mm

Connect to genset output N wire.

Mains R-phase Voltage
Monitoring Input

1.0mm

Connect to Mians R-phase, the controller uses 10A
fuse.

37 Mains N Wire Input

1.0mm

Connect to Mains N wire.

Connector A ( Connect to HGMS61D)

B+ IN

2.5mm

Connect Terminal 6 (B+ OUT) to this terminal
through a power switch to supply for positive post of
HGMS61M.

B+ OUT1

1.5mm

Supply power to positive post of HGMS61D.

B-

2.5mm

Negative post of controller power.

Содержание HGMS61
















































Результаты поиска

Содержание HGMS61

Отзывы:

Похожие инструкции для HGMS61

Бренды по названию

Популярные бренды

Smartgen HGMS61, Руководство пользователя

Результаты поиска

Содержание HGMS61

Отзывы:

Похожие инструкции для HGMS61

Бренды по названию

Популярные бренды