Smartgen HGMS61 Скачать руководство пользователя страница 15

Страница: 15 / 47

HGMS61 Genset Controller User Manual Page 15 of 47

5.2

SHUTDOWN ALARMS

When controller detects shutdown alarm, it will send signal to open switch and stop genset. The

alarms are displayed in LCD.

Table 8 – Shutdown Alarms

No.

Shutdown

Description

1 Emergency Stop

When controller detects emergency stop signal, it will send a stop alarm

signal and it will be displayed on LCD.

2 High Temp. Shutdown

When the temperature of water/cylinder is higher than set threshold, and

the high temp. shutdown inhibit is disabled or the high temp. input

shutdown inhibit is inactive, controller will send a stop alarm signal and it

will be displayed on LCD.

Low

Oil

Pressure

Shutdown

When oil pressure is lower than threshold, and low oil pressure shutdown

inhibit is disabled or the low oil pressure input shutdown inhibit is

inactive, controller will send a stop alarm signal and it will be displayed

on LCD.

4 Over Speed Shutdown

When genset speed is higher than set threshold, controller will send a

stop alarm signal and it will be displayed on LCD.

5 Under Speed Shutdown

When genset speed is lower than set threshold, controller will send a

stop alarm signal and it will be displayed on LCD.

Loss Of Speed Signal

Shutdown

When rotate speed is 0 and delay is not 0, controller will send a stop

alarm signal and it will be displayed on LCD.

Genset Over Voltage

Shutdown

When genset voltage is higher than threshold, controller will send a stop

alarm signal and it will be displayed on LCD.

Genset Under Voltage

Shutdown

When genset voltage is under set threshold, controller will send a stop

alarm signal and it will be displayed on LCD.

Genset Over Current

Shutdown

When genset current is higher than set threshold and delay is not 0, it will

send a stop alarm signal and it will be displayed on LCD.

10 Failed To Start

Within set start times, if fails to start, controller will send a stop alarm

signal and it will be displayed on LCD.

11 Over Freq. Shutdown

When genset frequency is higher than set threshold, controller will send a

stop alarm signal and it will be displayed on LCD.

12 Under Freq. Shutdown

When genset frequency is lower than set threshold, controller will send a

stop alarm signal and it will be displayed on LCD.

13 Genset Failed

When genset frequency is 0, controller will send a stop alarm signal and

it will be displayed on LCD.

14 Low Fuel Level

When low fuel level input is active, controller will send a stop alarm

signal and it will be displayed on LCD.

Содержание HGMS61
















































Результаты поиска

Содержание HGMS61

Отзывы:

Похожие инструкции для HGMS61

Бренды по названию

Популярные бренды

Smartgen HGMS61, Руководство пользователя

Результаты поиска

Содержание HGMS61

Отзывы:

Похожие инструкции для HGMS61

Бренды по названию

Популярные бренды