SMA SHP 125-US-20 Скачать руководство пользователя страница 67

Страница: 67 / 96

12 Troubleshooting

SMA Solar Technology AG

Operating manual

SHP-US-20-BE-en-10

Event number

Message, cause and corrective measures

3901
3902

Waiting for DC start conditions > Start cond. not met

The feed-in conditions for the utility grid are not yet fulfilled.

Corrective measures:

• Ensure that the PV array is not covered by snow or otherwise shaded.
• Wait for higher irradiation.
• If this message is displayed frequently in the morning, increase the

voltage limit for starting grid feed-in. Change the parameter

Critical

voltage to start feed-in

• If this message is displayed frequently with medium irradiation, ensure

that the PV array is correctly rated.

6001 to 6438

Self diagnosis > Interference device

The cause must be determined by the Service.

Corrective measures:

• Contact the Service.

6501
6502

Self-diagnosis > Overtemperature

The inverter has switched off due to excessive temperature.

Corrective measures:

• Clean the cooling fins on the rear of the enclosure and the air ducts on

the top using a soft brush.

• Ensure that the inverter has sufficient ventilation.
• Ensure that the inverter is not exposed to direct solar irradiation.

6511

Overtemperature

An overtemperature has been detected in the choke area.

Corrective measures:

• Clean the cooling fins on the rear of the enclosure and the air ducts on

the top using a soft brush.

• Ensure that the inverter has sufficient ventilation.
• Ensure that the inverter is not exposed to direct solar irradiation.

6512

Minimum operating temperature not reached

The inverter will only recommence grid feed-in once the temperature has
reached at least −25°C.

Содержание SHP 125-US-20

































































































Результаты поиска

Содержание SHP 125-US-20

Отзывы:

Похожие инструкции для SHP 125-US-20

Бренды по названию

Популярные бренды

SMA SHP 125-US-20, Руководство по эксплуатации

Результаты поиска

Содержание SHP 125-US-20

Отзывы:

Похожие инструкции для SHP 125-US-20

Бренды по названию

Популярные бренды