Page 38
INE S.p.A.
Via Facca, 10 - 35013 Cittadella - PADOVA - ITALIA Tel. 049/9481111 - Fax 049/9400249 - [email protected] - www.ine.it
15 Settings through generator interface
The controls of the machine are described here below
with reference to the following figures.
The machine can be switched on by turning to its ON
position the main switch, located at the back of the
generator. When the machine is on, the ‘L1’ green LED
is lit.
The ‘L2’ yellow LED indicates that protection devices
have tripped (e.g. fuse blown), and display ‘D1’ shows
which one has actually tripped (see paragraph
‘Description of alarms’);
The ‘L3’ red LED indicates, in MIG/MAG, that with the
set parameters a welding in ‘Globular’ mode is being
executed; this mode is advised against fir the sake of
the final welding result.
The ‘L4’ red LED indicates the presence of output
voltage. In electrode, it is constantly lit; in TIG and in
MIG/MAG, it follows the course of the welding cycle.
15.1 Settings for MMA welding
The operating mode switch ‘S1’ allows the choice of the
welding mode.
•
Press switch selector ‘E1’ for a while; the relevant led
will start blinking.
•
Turn the selector until the led corresponding to the
MMA
welding blinks (confirmation is automatic after
5 seconds of inactivity).
With selector switch ‘E5’ it is
possible to set at any time the
welding current, and its value
is shown on display ‘D1’. This
same display also shows,
while welding, the measured
voltage and current.
In MMA also you can set the following parameters:
•
Hotstart
HOT
:
percentage increase in
initial current; helps the electric arc
starting.
•
Arcforce
ARC
:
percentage increase in
welding current in the case of short
circuits; helps to prevent the shutdown
of the electric arc.
This procedure should be followed to change the former
parameters:
•
Press switch selector ‘E4’ for 2 seconds; the blue led
‘SET’ will start blinking.
•
Turn selector ‘E4’ to select the parameter to be
changed.
•
Turn selector ‘E5’ to change its value (a slider at the
bottom of the display will show the setting range).
•
Turn selector ‘E4’ to select any other parameter.
•
After changing the desired parameters, press ‘E4’ to
exit ‘SET’ mode.
Attention:
when choosing the MMA
welding, it is important, for avoiding risks and
dangerous situations, to check the position
of the MIG/MAG torch, as it will be energized
to the positive potential. (Thus you must avoid contact
with the piece being machined and with the earth
protection circuit.)
H
SI
L
G
N
E
KMP 5000
S
TIG HF
MMA
MIG DP
USER
MIG
MIG P
JOB
OK
A
ESC
V
AlSi
Flux
Rutil
ø1.0
ø1.0
Ar
2
Cored
CuSi
SPECIAL
AL
CuAl
AlMg
Metal
Wire
CrNi
ArCO
Basic
ø1.6
ø1.6
ø1.2
ø1.2
2
2
CO
2
SG2/3
SG2/3
CrNi
ArCO
NiCr
ArHe
ø0.8
ø0.8
kmp 5000
E5
L4
D1
E3
D2
E4
C5
L3
E2
L1
E1
L2
MMA
TIG HF
MIG P
MIG DP
MIG
USER
E1
OK
ESC
V
A
kmp 5000
D1
E4
E5
Содержание KMP3200
Страница 63: ......
