SkyAzúl Greer MG514 Скачать руководство пользователя страница 27

Страница: 27 / 90

2.6.4

Menu 03 - Zero Sensors

This menu allows the user to enter the zero point of the extension sensor.

1. Ensure the boom is completely retracted and at 0°. Verify with a digital level.
2. Press the

Next

Prev

button until “03 Zero Sensors” appears in the right of the information

window.

3. Press the

03 Zero Sensor

button to enter the routine.

4. Press the

Zero Extension? = XXX

button.

5. The extension sensor will now show

“Zero

No.2 = 0”

6. Press the

Next

button to enter the zero point for the angle sensor. This is done using the digital

level.

7. Press the

Zero No. 3 =X.XX

button.

The angle sensor will now show “Zero No. 3

= 0

”

TEST

SET

TEST

SET

SkyAzúl, Equipment Solutions

www.skyazul.com

301-371-6126

Содержание Greer MG514



























































































Результаты поиска

Содержание Greer MG514

Отзывы:

Похожие инструкции для Greer MG514

Бренды по названию

Популярные бренды

SkyAzúl Greer MG514, Инструкция по установке, калибровке и обслуживанию

Результаты поиска

Содержание Greer MG514

Отзывы:

Похожие инструкции для Greer MG514

Бренды по названию

Популярные бренды