background image

DOL 434 LPV

Technical Manual

3

Product and Documentation Changes

SKOV A/S reserves the right to change this document and the product herein described without further notice.
In case of doubt, please contact SKOV A/S.

The date of change appears from the front and back pages.

IMPORTANT!

Notes concerning alarm systems

Breakdowns, malfunctions or faulty settings may cause substantial damage and financial losses when regulat-
ing and controlling the climate in a livestock house. It is therefore essential to install a separate, independent
alarm system that monitors the house climate concurrently with the climate and production controller. According
to EU-directive No. 98/58/EU, an alarm system must be installed in all mechanically ventilated houses.

We would like to draw your attention to the fact that the product liability clause of general terms and conditions
of sale and delivery specifies that an alarm system must be installed.

In case of an operating error or inappropriate use, ventilation systems can result in production
losses or cause loss of lives among livestock.

We recommend that ventilation systems should be mounted, operated and serviced only by
trained staff and that a separate emergency opening unit and an alarm system be installed as well
as maintained and tested at regular intervals, according to terms and conditions of sale and deliv-
ery.

Installation, servicing and troubleshooting of all electrical equipment must be carried out by quali-
fied personnel in compliance with the applicable national and international standard EN 60204-1
and any other EU standards that are applicable in Europe.

The installation of a power supply isolator is required for each motor and power supply to facilitate
voltage-free work on the electrical equipment. The power supply isolator is not included.

Note

• All rights belong to SKOV A/S. No part of this manual may be reproduced in any manner whatsoever without

the expressed written permission of SKOV A/S in each case.

• All reasonable efforts have been made to ensure the accuracy of the information contained in this manual.

Should any mistakes or imprecise information occur in spite of this, SKOV A/S would appreciate being noti-
fied thereof.

• Irrespective of the above, SKOV A/S shall not accept any liability with regard to loss or damage caused or

alleged to be caused by reliance on any information contained herein.

• Copyright by SKOV A/S.

Содержание DOL 434 LPV





































































Отзывы: