Sirona cerec ac Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 84

background image

Sirona Dental Systems GmbH
Operating Instructions CEREC AC

8 Maintenance

8.1 Care, cleaning, disinfection and sterilization

63 33 582 D3492
D3492.201.01.22.02 10.2018

51

8.1.3

Non-critical surfaces excluding monitor screen

NOTE

Do not allow liquids to penetrate into the ventilation slots!

NOTE

Never use corrosive cleaning agents, wax or solvents.

➢ Use a new cotton gauze moistened with one of the cleaning agents

listed in the „Cleaning and disinfection agents [→ 50]“ section to
disinfect the non-critical contact surfaces of the CEREC AC like the
camera cradle, keyboard, and track ball. Discard this gauze.

Do not use any colored cloths for cleaning, since they may cause
discoloration of the surfaces, e.g. in combination with disinfectants!

Protection against medicaments

Due to their high concentrations and the substances they contain, many
medicaments can dissolve, etch, bleach or discolor surfaces.

NOTE

The only way to prevent damage is to wipe off medicaments
immediately with a damp cloth and a cleaning agent!

8.1.4

Trackball holder

1.

Rotate the cover ring counterclockwise and remove it.

2.

Clean inner surface of cover ring (A) with ethanol (commercially
available cleaning alcohol).

3.

Remove the ball.

4.

Wipe out the calotte (spherical cap).

5.

Insert the ball.

6.

Fit the cover ring and turn it clockwise until it is firmly tightened.

NOTE

Setting the ease of action of the ball

For cover rings with various detent positions, the ease of action of the
ball can be set by selecting the corresponding detent position.

8.1.5

CEREC Bluecam

CAUTION

If the CEREC Bluecam accidentally falls down, check to make sure
that the front lens and prism are not damaged. If the CEREC Bluecam
has been damaged, it must no longer be used on patients.

The CEREC Bluecam must be recalibrated.

NOTE

Do not sterilize the CEREC Bluecam or the camera cable!

NOTE

The prismatic tubes are not autoclave sterilizable!

«
...
49
50
51
52
53
...
»

Содержание cerec ac





















































































Отзывы:

Нет отзывов

Похожие инструкции для cerec ac

Бренд: PASCO Страницы: 2

Бренд: Leviton Страницы: 50

Бренд: Quick Charge Страницы: 4

V-CHARGE 100 DUO

Бренд: VOLTCRAFT Страницы: 236

Бренд: AlzaPower Страницы: 50

Бренд: DSR Страницы: 12

Бренд: LRP Страницы: 2

Бренд: Wentronic Страницы: 8

Бренд: Vimar Страницы: 4

Бренд: Ultra Products Страницы: 1

Бренд: Briggs & Stratton Страницы: 42

Бренд: BlackVue Страницы: 4

SpeedCharge SC-7500A

Бренд: Schumacher Electric Страницы: 2

Бренд: Schumacher Electric Страницы: 17

Бренд: Schumacher Electric Страницы: 23

Speed Charge SEM-1562A

Бренд: Schumacher Electric Страницы: 38

Бренд: Steren Страницы: 2

ProTask-1200 Series

Бренд: Mec Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды