Sirona cerec ac Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 84

background image

6 Installation and startup
6.5 Battery-backed operation (optional)

Sirona Dental Systems GmbH

Operating Instructions CEREC AC

36

6.4.9

Switching the units off

NOTE

Proper shutdown procedure

The operating system must always be shut down properly to prevent
data loss.

1.

Exit all programs.

2.

Power down the operating system.

Ä

The PC automatically switches off. The operating state LED
lights up yellow.

NOTE

Do not switch off while battery (optional) is being charged

The battery will be charged only if the power cord is plugged in and
the main switch at the back of the unit is switched on (see also
Charging the battery (optional) [→ 68]).

3.

Switch the acquisition unit off at the main switch.

Ä

The operating state LED goes out.

NOTICE: Now you can also switch the milling unit off if necessary.

6.5

Battery-backed operation (optional)

Introduction

The acquisition unit PC has a battery-backed power supply. It is thus
possible to operate the acquisition unit for a short time with no line
voltage connected.

CAUTION

No treatment without connected line voltage

Treating a patient (generating intraoral acquisitions) is not permitted if
the unit is not connected to the power supply of the practice.

The following parameters are constantly checked by the installed
monitoring software in order to monitor the battery back-up function:

● Line voltage present:

● Charge set of storage battery pack

● Fan function

● Temperature of power supply

When the unit is running in the battery-powered mode, this is indicated
by a message displayed at the bottom of the screen. It is accompanied
by a rhythmic beep.

This beep changes to a continuous signal 30 seconds before the
system shuts down due to insufficient battery power. A corresponding
display then appears in the center of the screen. The user thus has time
to finish his last actions on the PC.

As soon as 30 seconds have elapsed, the operating system is shut
down.

«
...
34
35
36
37
38
...
»

Содержание cerec ac





















































































Отзывы:

Нет отзывов

Похожие инструкции для cerec ac

X-Peak 80 BAL Pult Edition

Бренд: Jamara Страницы: 28

Бренд: Vante Страницы: 12

Бренд: CHARGit Страницы: 9

Бренд: JAR Systems Страницы: 5

Abso Charger 12V 20A

Бренд: Kisae Страницы: 21

PerfectBattery BC400

Бренд: Waeco Страницы: 140

Бренд: GoPro Страницы: 12

Бренд: Samlexpower Страницы: 17

Бренд: Skyrc Страницы: 24

Бренд: XU1 Страницы: 2

5-Hour AA & AAA Ni-Cd/Ni-MH Battery Charger

Бренд: Radio Shack Страницы: 4

Бренд: BTI Страницы: 32

Бренд: Zamp Solar Страницы: 8

Бренд: NEC Страницы: 71

Бренд: NEC Страницы: 174

Бренд: Xantrex Страницы: 62

Бренд: WONGOX Страницы: 2

Бренд: Stanley Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды