Simrad AP35 Скачать руководство пользователя | Manualshive

Страница: 73 / 104

background image

Installation

22083083H

71

4.32

Software Setup Procedure

Description of Installation Settings

The design of the AP35 includes advanced features that have simplified the
installation and setup of an autopilot. The principle advantage is that manual
adjustments that needed to be done on previous models are no longer
necessary with the AP35.

Note !

The installation settings must be performed as part of the installation of the
AP35 system. Failure to correctly set the values in the installation settings
may prohibit the AP35 from functioning properly!

The Installation Settings are grouped into the following functional
categories:

•

Language:

Selects language used for display information

•

Dockside Settings:

Sets values of items to be set prior to seatrials

•

Interface Setup:

Sets the identification of navigation and optional

equipment connected to the AP35 system

•

Seatrial Settings:

Determines automatic calibrations and steering

parameters

•

View Parameters

Permits viewing, setting, or changing steering

parameters

Each group is designed to focus on specific functions related to an
installation activity, and enable quick access when changes need to be made.

Some important points regarding the installation settings values:

•

When the AP35 is delivered new from the factory, (AND ANY TIME
AFTER A MASTER RESET OF MEMORIES HAS BEEN
PERFORMED) the Installation Settings are all reset to preset (default)
values. The warning message "Installation Setup Required" will appear at
turn on and if an attempt is made to access the AUTO or NAV modes.

•

The Dockside, Interface and Seatrial settings can only be accessed when
the system is in STBY mode.

•

The values that are selected (also referred to as "PARAMETERS") from
within the Installation Settings Menu, are stored in the memory of the
AP35 system. No specific action is required to "SAVE" the selected
values. Once the value is changed, it is stored until the next time the
menu item is selected and changed.

•

The Installation Settings are considered global, enabling values to be
available to all control units in the system.

•

The values in the Seatrial Settings are dependent on successful
completion of the Dockside Settings.

Before attempting to turn on the AP35 and perform an Installation Setup, the
hardware installation and electrical installation must be completed in
accordance with the installation instructions.

«
...
71
72
73
74
75
...
»

Содержание AP35









































































































Отзывы:

Нет отзывов

Похожие инструкции для AP35

Бренд: Samsung Страницы: 22

Бренд: M-Audio Страницы: 12

Aqua-Pure 3MFF100

Бренд: 3M Страницы: 8

Бренд: Danley Страницы: 8

Бренд: Watts Страницы: 10

Бренд: Hengbida Electronic Technology Страницы: 19

Basix BSX-MHB-HCW

Бренд: MECHLINE Страницы: 16

Бренд: Pioneer Страницы: 2

Бренд: Pioneer Страницы: 9

Бренд: Pioneer Страницы: 96

Бренд: Panasonic Страницы: 70

Бренд: Panasonic Страницы: 74

Бренд: Panasonic Страницы: 125

Бренд: Panasonic Страницы: 132

Бренд: Panasonic Страницы: 139

Бренд: Panasonic Страницы: 143

Бренд: Panasonic Страницы: 73

Бренд: Panasonic Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды