Simrad AP35 Скачать руководство пользователя | Manualshive

Страница: 20 / 104

background image

Simrad AP35 Autopilot

18

22083083H

2.7

R3000X Remote Control

Note!

When in AUTO/WORK mode, pressing
the buttons will change the set course
1° per push. If you keep the button
pressed, it will automatically change
the course in increments of 3°/second.

Operation of mode button returns the
autopilot to initial mode except when in
Nav mode:
AUTO

→

STBY

→

AUTO

WORK

→

STBY

→

WORK

NAV

→

STBY

→

AUTO

Nav and Work modes can only be
entered from the control unit.

2.8

S35 NFU Steering Lever

STBY:

The rudder will move as long as the lever is offset to Port
or Stbd (NFU steering). The mode button is lit each time
the lever is offset.

AUTO/WORK: The set course will be changed by 3°/sec. when the lever

is offset to port or Stbd.

The mode button remains lit as long as the autopilot is in
AUTO or WORK mode (and NAV mode).

Mode change sequence is as follows:

AUTO

AUTO

STBY

STBY

WORK

WO RK

Operation of mode button returns the autopilot to initial
mode.

NAV:

It is not possible to change set course by the lever.
Pressing the mode button brings the autopilot to Stby
mode, but next press brings it to Auto mode, not back to
Nav mode.

STBY

NAV

AUTO

Note !

NAV and WORK mode can only be entered from a control unit.

STBY-AUTO

Simrad R3000X

STBY/AUTO mode button.
AUTO, WORK or NAV
mode is when lamp is lit

Push buttons for Port and
Stbd NFU commands

SIMRAD

«
...
18
19
20
21
22
...
»

Содержание AP35









































































































Отзывы:

Нет отзывов

Похожие инструкции для AP35

Бренд: Skytec Страницы: 12

Бренд: TANDBERG Страницы: 12

Бренд: Watts Страницы: 24

Бренд: SAL Страницы: 20

Бренд: S.E.M. Страницы: 6

Бренд: Armstrong Страницы: 2

Бренд: Philips Страницы: 22

Бренд: Philips Страницы: 25

CMT-BX20i Marketing

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

CMT EH15 - Micro HI-FI Stereo Music System

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 1

Бренд: Sony Страницы: 24

Бренд: Sony Страницы: 26

Бренд: Sony Страницы: 32

Бренд: Sony Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды