Simrad AP35 Скачать руководство пользователя

Страница: 5 / 104

Instruction Manual

22083083H

Contents

GENERAL INFORMATION ............................................................................................... 9

1.1

Introduction .............................................................................................................. 9

1.2

How to use this manual............................................................................................. 9

1.3

System components ................................................................................................ 10

1.4

AP35 Control Unit.................................................................................................. 10

1.5

Junction units.......................................................................................................... 11

1.6

Rudder Feedback units ........................................................................................... 11

RF300 Rudder Feedback Unit ................................................................................ 11

RF45X Rudder Feedback Unit ............................................................................... 11

1.7

Heading Sensors ..................................................................................................... 11

RFC35 Electronic Fluxgate Compass..................................................................... 11

RC25 Rate Compass ............................................................................................... 12

CDI35 Course Detector Interface and CD100A (CD109) Course Detector........... 12

NMEA compass...................................................................................................... 12

Other compass models............................................................................................ 12

1.8

Optional equipment ................................................................................................ 12

R3000X Remote Control ........................................................................................ 12

S35 NFU Steering Lever ........................................................................................ 12

FU50 Follow-Up Steering Lever ............................................................................ 12

F1/2 NFU Remote .................................................................................................. 13

RI35 Mk2 Rudder Angle Indicator......................................................................... 13

OPERATION OF THE AUTOPILOT............................................................................... 15

2.1

Overview ................................................................................................................ 15

2.2

ON/OFF - Standby mode........................................................................................ 16

2.3

Follow-Up steering ................................................................................................. 17

2.4

Non-Follow-Up steering......................................................................................... 17

2.5

NFU Steering lever................................................................................................. 17

2.6

NFU Push button remote control............................................................................ 17

2.7

R3000X Remote Control ........................................................................................ 18

2.8

S35 NFU Steering Lever ........................................................................................ 18

2.9

Automatic Steering ................................................................................................. 19

2.10

Automatic Speed selection ..................................................................................... 20

2.11

Manual speed selection........................................................................................... 20

2.12

Navigating with the AP35 ...................................................................................... 21

Selecting a different Navigator............................................................................... 22

2.13

WORK-mode.......................................................................................................... 23

2.14

TURN-mode ........................................................................................................... 24

2.15

Dodging .................................................................................................................. 25

Dodge in NAV........................................................................................................ 25

2.16

Multiple station system........................................................................................... 25

2.17

Lock function.......................................................................................................... 26

2.18

User Set-up Menu ................................................................................................... 27

TECHNICAL SPECIFICATIONS..................................................................................... 29

Содержание AP35









































































































Результаты поиска

Содержание AP35

Отзывы:

Похожие инструкции для AP35

Бренды по названию

Популярные бренды

Simrad AP35, Инструкция по эксплуатации

Результаты поиска

Содержание AP35

Отзывы:

Похожие инструкции для AP35

Бренды по названию

Популярные бренды