Simrad AP35 Скачать руководство пользователя | Manualshive

Страница: 29 / 104

background image

Operation

22083083H

27

2.18

User Set-up Menu

NAV

SETUP

- SETUP -

Backlight

03

- SETUP -

Contrast

05

- SETUP -

Seastate
Filt.: OFF

- SETUP -

NAV. source:
GPS 1

- SETUP -

POS. Source:

GPS 1

Sequences
FWD in MENU

Sequences
BACK in
MENU

Adjust backlight of display and pushbuttons (10 steps,
10 = brightest). Setting is stored when system is
turned off, and resets to stored level at turn on.
Adjustment is local to the control head you adjust.

Adjust contrast of displays (10 steps). Setting is stored when
system is turned off, and resets to stored level at turn on.
Adjustment is local. All steps not available at high temperature
due to automatic temperature compensation.

Select the compass to be used for AUTO steering.
Refer to the interface setup table in section 4.
RFC COMP = Robertson Fluxgate compass
MAGNET COMP = Magnetic compass
OTHER FLUXG = Non-Robertson fluxgate compass (sin/cos)
GYRO COMP = Robertson gyrocompass (using 1:1 synchro)
NMEA COMP = NMEA compass

Scrolls through menu
selections or sets
value on menu items

Set the Sea State filter.
OFF: Provides precise steering but increases rudder activity.
AUTO: Reduces rudder activity and reduces sensitivity of
autopilot in rough weather automatically.
MANUAL: Sets yawband manually (1-10).

Select the source for NAV mode steering.
Refer to interface setup table in section 4.

Select the source of speed over ground (SOG) and position data
processed by the AP35. This option will appear whenever there is
more than one navigation receiver connected to the system.

Except when NMEA TEST or SYSTEM DATA is displayed, the menu
will disappear after 60 seconds if no key is pressed. It will disappear
immediately if any mode key (STBY, AUTO, NAV, WORK, TURN)
is pressed.

- SETUP -

Select Comp.:
RFC COMP.

Test functions for analysing system data (See "NMEA test" and
"System Data menu" under the "Trouble shooting" section).

NMEA TEST?

SYSTEM DATA?

Quick double

press

Enter User

Setup Menu

Displays User

Set-up Menu

- SETUP -

Backlight

03

TOP

BACK

FWD

STBD

PORT

STBD

PORT

Note !

It is necessary to select the correct compass and Nav. source to make the
autopilot operate.

«
...
27
28
29
30
31
...
»

Содержание AP35









































































































Отзывы:

Нет отзывов

Похожие инструкции для AP35

Бренд: Water Factory Systems Страницы: 15

Бренд: Panasonic Страницы: 2

Бренд: AeroAudio Страницы: 8

2JT Cartridge EV9608-10

Бренд: Everpure Страницы: 2

ETR 2000 series

Бренд: Delco Страницы: 34

Бренд: IDEAL Страницы: 68

Бренд: SONIQ Страницы: 7

Бренд: Fuslon Страницы: 14

Бренд: Teac Страницы: 23

Бренд: Daewoo Страницы: 29

Бренд: Sharp Страницы: 40

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды