Simrad AP35 Скачать руководство пользователя | Manualshive

Страница: 14 / 104

background image

Simrad AP35 Autopilot

12

22083083H

RC25 Rate Compass

Fluxgate compass with integrated rate of turn sensor. Provides a dramatic
improvement to the dynamic performance of both the autopilot and a
stabilized radar display.

Same dimensions as RFC35.

CDI35 Course Detector Interface and
CD100A (CD109) Course Detector

Interface and sensor unit to connect AP35 to a magnetic compass. The AP35
provides excitation current for CD100A and converts the analogue sin/cos
signal to digital two wire format for the autopilot steering computer.

NMEA compass

Any NMEA 0183 compass with HDT, HDG or HDM messages can be
connected directly to the J300X/J300-40X junction units.

Other compass models

The optional CI300X can interface AP35 to fluxgate compasses with
heading signal on a sine/cosine format or gyro with 1:1 synchro.

1.8

Optional equipment

A series of options are available for the basic AP35 system.

R3000X Remote Control

A small handheld remote control with two push buttons for power steering
or course selection (port and starboard), and one push button with built-in
lighted indicator for mode selection.

S35 NFU Steering Lever

S35 is designed for indoor and outdoor bulkhead mount and made of shock
resistant polyxymethylene. The lever has spring loaded return to mid-
position. A push button with light indicator is used for mode selection when
connected to a Simrad J3XX junction unit.

FU50 Follow-Up Steering Lever

The FU50 Follow-up steering lever features a dial (scale) with 5° rudder
angle markings. The rudder will move and stop at the angle selected on the
dial. The FU50 has a mid-position indent, buttons for (limited) mode
selection, and mode indicators (STBY, FU, AUTO, NAV, WORK, and
THRUSTER*). It is designed for indoor and outdoor bulkhead- or panel-
mounting. Refer to the FU50 manual.

* With AP50 Autopilot only.

«
...
12
13
14
15
16
...
»

Содержание AP35









































































































Отзывы:

Нет отзывов

Похожие инструкции для AP35

Water Jet Lightning

Бренд: Oase Страницы: 28

Бренд: Oase Страницы: 9

Бренд: DAPAudio Страницы: 17

Бренд: Craig Страницы: 2

Бренд: Sharp Страницы: 18

Бренд: Sound Ryder Страницы: 20

Бренд: Sony Страницы: 16

Бренд: Sony Страницы: 22

HCD-GRX33 - Component For Mhcrx33

Бренд: Sony Страницы: 32

Бренд: Sony Страницы: 54

Бренд: Sony Страницы: 62

Бренд: Sony Страницы: 72

Бренд: Sony Страницы: 70

Бренд: Sony Страницы: 72

Бренд: Sony Страницы: 68

Бренд: Sony Страницы: 66

Бренд: Sony Страницы: 71

Бренд: Sony Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды