Simrad AP35 Скачать руководство пользователя

Страница: 61 / 104

Installation

22083083H

•

Connect the Robnet connector to the AP35 Control Unit (or CI300X or
NI300X if installed), see Figure 4-16.

•

Alternatively, if there is no free receptacle, cut the connector from the
cable and connect the wires in parallel with the wires going from the
junction unit to the control unit (see Figure 4-13).

Do not connect the

yellow and the green wires and ensure that they do not connect with the
terminal or chassis.

•

Select RFC = ROBNET in the Installation : Interface Setup.

•

Select RFC as compass in the User Setup Menu.

•

Perform the compass calibration as described on page 84.

Note !

After turning on, the compass will stabilize in less than 30 seconds, but it
will need another 5 minutes to get the full effect of the rate sensor.

Refer to page 84 to compensate for any permanent off-set after the
calibration is completed.

RC25 calibration data is stored in the compass and will not be deleted by a
Master Reset in the autopilot.

4.13

R3000X Remote Control

R3000X should be mounted in the supplied bracket that can be fixed by four
mounting screws. The unit is weather proof and can be mounted outdoor.

TB6

JUNCTION UNIT

TB3 TB4

TB5

TB7

Po
rt

Gn
d

Gn Red Blu

R E M O T E

T B 8

T B 1 T B 2

R3000X

REMOTE CONTROL

La
m

Yel

POWER PCB

Figure 4-17 R3000X connection

4.14

FU50 Steering Lever

For connection of the FU50 Steering Lever, see the FU50 manual.

Содержание AP35









































































































Результаты поиска

Содержание AP35

Отзывы:

Похожие инструкции для AP35

Бренды по названию

Популярные бренды

Simrad AP35, Инструкция по эксплуатации

Результаты поиска

Содержание AP35

Отзывы:

Похожие инструкции для AP35

Бренды по названию

Популярные бренды