Simplex F18804 Скачать руководство пользователя

Страница: 21 / 40

Product range

The illustrations are symbolic and may deviate from the respective product.
Subject to technical modifications and errors.

8.4. Power supply

Ensure correct polarity

If intended or prescribed for pumps, connect the protective earth conductor to the protective earth connection terminals of the

controller. Observe the following points: Ensure that the protective earth conductor is also connected to the controller on the power

supply side.

Strain relief using flexible cables required: the enclosed cable ties must be used and tightened so that the cable cannot come loose.

8.5. Connect Secos temperature sensor for supply line

a. When connecting to the controller, it is not necessary to pay attention to polarity.

A cable with 2 x 0.5 mm² can be used to extend the sensor up to 2 m.

Sensor is already mounted in immersion sleeve.

8.6. Connect Secos system bus

a. Insert plug, if necessary use extension (optional accessory)
b. 1x Bus cable ready to plug in, twist-proof.

Secos

- Simplex Energy Control System

Installation instructions

Operating instructions

Содержание F18804









































Результаты поиска

Содержание F18804

Отзывы:

Похожие инструкции для F18804

Бренды по названию

Популярные бренды

Simplex F18804, Инструкции по установке и эксплуатации

Результаты поиска

Содержание F18804

Отзывы:

Похожие инструкции для F18804

Бренды по названию

Популярные бренды