Silex technology MNS-300EM Скачать руководство пользователя страница 99

Страница: 99 / 134

10. TCP/IP Commands

Allows/Denies access from the specified IP address range.

SET IP ACcess [ENable | DISable | ALL] <aa.bb.cc.dd> <ee.ff.gg.hh>

This command updates the list of IP addresses that can access MNS-300EM.

ENable

: Adds an IP address range to the IP address list. Only the hosts with the

registered IP address are allowed to access MNS-300EM.

DISable

: Removes an IP address range from the IP address list when it is found on

the list.

ALL

: Clears the IP address list and allows access of all hosts.

aa.bb.cc.dd and
ee.ff.gg.hh

: Specifies the IP address range. The IP addresses in the range of aa.bb.

cc.dd to ee.ff.gg.hh will be the target of operation.

SH IP ACcess

SH IP RANge

can show the settings of IP address list.

Specifies the interval to send Gratuitous ARP packets (minutes).

SET IP KEepalive <n>

Enter the transmission interval for <n>.
The factory default value is

(minutes).

10-2. SET IP ACcess

10-3. SET IP KEepalive

Содержание MNS-300EM






































































































































Результаты поиска

Содержание MNS-300EM

Отзывы:

Бренды по названию

Популярные бренды

Silex technology MNS-300EM, Руководство по управлению

Результаты поиска

Содержание MNS-300EM

Отзывы:

Бренды по названию

Популярные бренды