Silex technology MNS-300EM Скачать руководство пользователя страница 34

Страница: 34 / 134

MNS-300EM Command Manual

This is a test command to force the version 0 protocol to be used for the PEAP authentication.

SET NW PEAPV0 [ENable | DISable]

Enable/Disable mandatory use of the version 0 protocol.

ENable

: Enables mandatory use of the version 0 protocol.

DISable

: Disables mandatory use of the version 0 protocol.

This command can be enabled when the wireless LAN authentication method is PEAP, and
is implemented for protocol tests. Usually,

DISable

is selected for a normal operation.

The factory default value is

DISable

SH NW PEAPV0

can show the current setting

4-2-12. SET NW PEAPV0

Changes the password of private key file to be registered to MNS-300EM.

SET NW PKPASS <passphrase>

For <passphrase>, enter a string with 8-63 alphanumeric characters.
The value has to be set before the key file is registered, otherwise the file cannot be
decoded properly.

The factory default value is a NULL string.

Example:

Local> SET NW PKPASS keypassword

4-2-13. SET NW PKPASS

Содержание MNS-300EM






































































































































Результаты поиска

Содержание MNS-300EM

Отзывы:

Похожие инструкции для MNS-300EM

Бренды по названию

Популярные бренды

Silex technology MNS-300EM, Руководство по управлению

Результаты поиска

Содержание MNS-300EM

Отзывы:

Похожие инструкции для MNS-300EM

Бренды по названию

Популярные бренды