Silex technology MNS-300EM Скачать руководство пользователя страница 47

Страница: 47 / 134

4. Station Commands

Changes the IP address configuration method for Station mode.

SET IP MEthod [ AUTO | DHCP | STATIC ]

Choose one of the following configuration methods.

AUTO

: Tries to get an IP address using the DHCP protocol.
When it fails, a static IP address of MNS-300EM is used.

DHCP

: Tries to get an IP address using the DHCP protocol.
When it fails, a link-local address is used.

STATIC

: A static IP address of MNS-300EM is used.

The factory default value is

AUTO

Specifies the IP address to use for Station mode.
To assign a static IP address to MNS-300EM, use this command to specify the IP address.

SET IP ADdress <aa.bb.cc.dd>

Enter the IP address for <aa.bb.cc.dd>.
The factory default value is

169.254.111.111

4-6. TCP/IP Settings in Station Mode

4-6-1. SET IP MEthod

4-6-2. SET IP ADdress

The following describes the commands for TCP/IP setting for Station mode.

Содержание MNS-300EM






































































































































Результаты поиска

Содержание MNS-300EM

Отзывы:

Бренды по названию

Популярные бренды

Silex technology MNS-300EM, Руководство по управлению

Результаты поиска

Содержание MNS-300EM

Отзывы:

Бренды по названию

Популярные бренды