Silex technology MNS-300EM Скачать руководство пользователя страница 85

Страница: 85 / 134

8. Service Commands

Sets the index number of the end of transmission (EOT) string for the specified service.

SET SERVI <service name> EOT <n>

service name

: Specifies the service name.

: Specifies the index number. The string of the index number will be the EOT

string.

The string of the specified index number is sent at the end of output.
The factory default value is a NULL string.

Shows the BOT and EOT strings to use for the service.

SH SERVI STRings [string_num]

When string_num is specified

: Shows the string definition of the specified number and the

extended information.

When string_num is not specified

: Shows all string definitions without the extended information.

Sample output:

Local> SH SERVI STR 10

10: \FF\04\FF\05\FF\06\FF\08

8-3. SET SERVI <service name> EOT

8-4. SH SERVI STRings [string_num]

Содержание MNS-300EM






































































































































Результаты поиска

Содержание MNS-300EM

Отзывы:

Бренды по названию

Популярные бренды

Silex technology MNS-300EM, Руководство по управлению

Результаты поиска

Содержание MNS-300EM

Отзывы:

Бренды по названию

Популярные бренды