Silex technology MNS-300EM Скачать руководство пользователя страница 90

Страница: 90 / 134

MNS-300EM Command Manual

Specifies the operation to take when a Raw TCP port is defined and the server is busy with
the other jobs.

SET SERVI <service name> QUEue [ENable | DISable]

service name

: Specifies the service name.

ENable

: The server queues the job that is to be sent to the port.

DISable

: The job is denied.

The factory default value is

DISable

8-14. SET SERVI <service name> QUEue

Shows the priority for the specified services.

SH SERVI PRI [service_num]

For [service_num], enter the number of the service to show the priority.
When no value is given, priority for all services will be shown.

Sample output:

Local>
# Service Priority
1 SDS40CB90_S1_A 10
2 SDS40CB90_S1_B 10
3 SDS40CB90_S2_A 10
4 SDS40CB90_S2_B 10

8-13. SH SERVI PRI [service_num]

Содержание MNS-300EM






































































































































Результаты поиска

Содержание MNS-300EM

Отзывы:

Бренды по названию

Популярные бренды

Silex technology MNS-300EM, Руководство по управлению

Результаты поиска

Содержание MNS-300EM

Отзывы:

Бренды по названию

Популярные бренды