Silex technology MNS-300EM Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 134

background image

58

MNS-300EM Command Manual

6-2-3. SET PORT S1 ECADDR

Sets the primary destination address for E-Cable connection.

SET PORT S1 ECADDR <dest-addr>

For <dest-addr>, enter the primary address (IP address) of the host device to which the I/O
port data is sent. When DNS is enabled only for the TCP mode, a host name can be used to
enter the command.

When 0.0.0.0 is entered, no data can be sent.
The factory default value is

0.0.0.0

.

6-2-4. SET PORT S1 ECCONN

Sets the interval for connection retry in case TCP connection is lost or cannot be
established. This setting is valid for TCP mode only.

SET PORT S1 ECCONN <n>

Specify the interval of connection retry for <n>.
The configurable time unit and interval will vary depending on the ECTMMSEC setting that
is enabled/disabled by

SET PORT S1 ECTMMSEC.

When ECTMMSEC is enabled

: The valid range is 20-2550. (Unit: Millisecond).

When ECTMMSEC is disabled

: The valid range is 1-255. (Unit: Second).

When a value out of the valid range is specified, the upper or lower limit of the range will
be applied. The factory default value is

30

(seconds).

When 0 is given for <n>, the default value (30) will be applied.

«
...
68
69
70
71
72
...
»

Содержание MNS-300EM







































































































































Отзывы:

Нет отзывов

Похожие инструкции для MNS-300EM

Бренд: jbc Страницы: 4

Бренд: Febco Страницы: 4

Бренд: Cisco Страницы: 48

Бренд: 3M Страницы: 34

Бренд: YOKOGAWA Страницы: 2

ALICAT SCIENTIFIC PC

Бренд: Halma Страницы: 2

ALICAT SCIENTIFIC PCD

Бренд: Halma Страницы: 46

Бренд: Fingertips Lab Страницы: 15

TruPortal TP-ADD-1DIP

Бренд: Interlogix Страницы: 9

Бренд: Sunnen Страницы: 24

FX-COMM4NDER MFX3203

Бренд: Magicfx Страницы: 16

Total Access 351 Series

Бренд: ADTRAN Страницы: 4

LOWARA Aquavara IPC

Бренд: Xylem Страницы: 292

Бренд: DSC Страницы: 16

Бренд: Redback Страницы: 3

Бренд: IEI Technology Страницы: 6

DYGIZONE GJD910

Бренд: GJD Страницы: 13

SE - 566 80 Habo

Бренд: Fagerhult Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды