manualshive.com logo in svg

Silex technology MNS-300EM, Руководство по управлению

Поделиться
Скачать
Silex technology MNS-300EM Скачать руководство пользователя страница 94

82

MNS-300EM Command Manual

Registers the string to use for services. 

SET STRing <string_num> <"value">

string_num

: Specifies the number where the string is registered. 

value

: Specifies the string to register. The string has to be double-quoted. 

When 

/

 is added to the beginning of the string, two hexadecimal digits can be specified.  

When 

/FF

 is added to the beginning of string, the registered index number of the string 

can be specified. The string of the specified index number will be used for the service. 

Sample output: 

SET STRing 12 "/AE"

 

 

Registers hexadecimal "AE" at 12th.

SET STRing 13 "/FF/04/FF/05"

 

 

Registers the 4th and 5th strings to 13th. 

9-1. SET STRing 

Deletes the string that is used for services. 

CL STRing <string_num>

For <string_num>, enter the number of the string to delete.

9-2. CL STRing

•  Strings from 1st to 11th cannot be changed.

TIP

Содержание MNS-300EM







































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды